KatriniQJ submersible pumpDoes deformation affect the effect

　　 drainage and water injection with vacuum equipment: the self exhaust of centrifugal pump is the same as the negative pressure exhaust of vacuum pump, so the water ring vacuum pump is used for exhaust to achieve the of water inlet.　　The water pump can be used to transport and pressurize clean water without impurities, such as apartment, residence,KatriniSubmersible non clogging slurry pump, villa water supply, factory water supply, water supply system drinking water system and water treatment. In short, there are many uses.Katrini,　　It will also be higher, but there is no specific conversion standard. Generally speaking, the suction lift of ISG pipeline pump shall not be greater than m without adding any auxiliary equipment.　　The high-efficiency slurry pump has three characteristics: first, the slurry pump has high operation efficiency and low loss.Zaysan, the outlet gate valve shall be (closed or slightly opened by /. Before starting the slurry pump, expand the pump inlet valve and close the pump outlet valve. Then start the pump. After the pump is started, slowly start the pump outlet valve. The size and speed of opening the pump outlet valve should be based on the fact that the pump does not vibrate and the motor　　Body. So that the pump can realize high concentration transmission without auxiliary devices. The unique sealing device can effectively balance the pressure inside and outside the oil chamber, so that the pressure at both ends of the mechanical seal can be kept balanced, which maximizes the reliable operation of the mechanical seal and greatly extends its service life　　The Tao part also consumes part of it.

　　 The slurry pump mainly aims at conveying flow, so the flow meter (meter) shall be installed in the operation monitoring system as far as possible to monitor whether the flow meets the requirements at any time; In the pipeline system, slag flushing system and pressure filtration dehydration system equipped with hydrocyclone, certain　　Fire fighting awareness is deeply rooted in the hearts of the people. With the improvement of fire fighting awareness many people pay more and more attention to fire pumps. Some places also began to pay attention to the selection of fire pumps. In many places, fire control　　Different installation requirements: the vertical slurry pump needs to be fixed, while the submersible slurry pump does not need to be fixed. It can directly invade into the liquid for operation.Product range,　　It is an auxiliary means of on-site monitoring. During the operation of the submersible slurry pump, the condition of its overflow parts is very important to the overall operation. In order to let everyone know more about the equipment, we will learn how to adjust the impeller clearance of the pump in this issue. I hope it will help you.　　About %), and motor power p=i × U indicates that high power and current will increase.　　When in use, it can drive the impeller to rotate so as to drive it to flow.

　　When using the sand pump, be sure to pay attention to the steering divergence between the motor and the pump. The sand pump has an arrow on the pump to mark the main steering. After the power supply is connected, run the pump without load. Check whether the motor operates normally. During operation, be careful not to exceed the bearing on the pump support to avoidPotential development,　　Troubleshooting: first increase the water pressure, then inject water into the pump body, and then start the pump. At the same time,KatriniDeep well pump, check whether the check valve is tight and whether the pipes and joints leak. If air leakage is found, apply lubricating oil or mixed paint on the joint after disassembly and tighten the screws.　　Is the submersible sewage pump a submersible pump or a sewage pump QW (WQ) submersible non clogging sewage pump QW (WQ) submersible non clogging sewage pump: the pump adopts a unique single or double blade impeller structure, which greatly improves the sewage passing capacity and can effectively pass through times the fiber material and diameter of the pump diameter　　Body. So that the pump can realize high concentration transmission without auxiliary devices. The unique sealing device can effectively balance the pressure inside and outside the oil chamber, so that the pressure at both ends of the mechanical seal can be kept balanced,　　If the submersible slurry pump cannot be installed and operated, the blank operation point can be supplemented.　　 If the head of the submersible slurry pump is too low or the head is higher than the practical condition, the flow will be large and the current will rise. At this time, the outlet valve can be turned down to increase the resistance to control the current.　　 One frequency converter with one slurry pump is adopted for installation. The specific transformation method is as follows: close the return valve, adopt the water level closed-loop control mode, install the liquid level sensor on the inner wall of the tank by the manufacturer of the slurry pump, and use the PID adjustment of the frequency converter. When