LimassolSubmersible slurry pumpProduct performance characteristics

　　The development of submersible slurry pump is to adapt to increasingly complex working conditions, facilitate users to use, and its use mode is more flexible. And it fills a part of the gap in the application of slurry pump. When the submergence depth is deep and there is no better slurry outlet, that is, in the traditional slurry pump　　First, let&#;s talk about the familiar vertical slurry pumps. Here we refer to ZJL and SP submerged slurry pumps. Strictly speaking the submersible slurry pump is also a vertical slurry pump, because its axis is basically vertical when it works, but it can be completely immersed in water when it runs,LimassolSubmersible pump can pump sewage, so it is a good choiceLimassol,　　 When the electric pump is not in use, take it out of the water and do not immerse it in the water for a long time, so as to reduce the chance of the motor stator winding getting damp and increase the service life of the electric pump. When the temperature is low, the pump needs to be lifted out to prevent freezing.　　 repair and level the welding part of the submersible slurry pump with a file, clean the part to be bound with alcohol again and wipe it dry.Xu dat　　Rate.　　When using the sand pump, be sure to pay attention to the steering divergence between the motor and the pump. The sand pump has an arrow on the pump to mark the main steering. After the power supply is connected, run the pump without load. Check whether the motor operates normally. During operation, be careful not to exceed the bearing on the pump support to avoid　　Submersible slurry pump Use ultrasonic method to detect whether there is cavitation in the submersible slurry pump. This method is often convenient for re detection. Even if there is some noise in the surrounding environment, it will not affect the detection results. Therefore, many pumps often have better measurement results when in use.

　　Only in this way can its service life be extended to a large extent.　　 After one year of use, check the corrosion of the pump, remove the rust and paint. If the submersible pump is not used for a long time, it should be carefully checked and put dry.　　 Selection of pipeline diameter: the selection of pipeline shall consider the one-time purchase cost, long-term operation cost and operation reliability.Direct labor,　　Start the priming pump. Moreover, due to the structural limitations of the submersible slurry pump the motor needs to be placed on the water surface for use during operation, and then the pump needs to be placed in the water for use. Therefore, the submersible slurry pump must be　　Some impurities will entangle the impeller, so generally, the open impeller will be used, so there is no need to worry about getting stuck in the process of transporting sewage.　　Sex is different. Although the submersible slurry pump is widely used, the correct application is very important. Due to the limitation of the name of the slurry pump, some people outside the industry misunderstand this. In fact, the impurity pump, desilting pump, etc. are all in the application scope of the slurry pump

　　Submersible slurry pumps are mainly used in mining, metallurgy, coal, environmental protection, electric power and other industries to transport corrosive solid particle slurry. For example, in the field of chemical industry, coal washing plant slurry transportation, etc. Submersible slurry pump bladeTotal quality assurance,　　The pump can often be selected according to the specific requirements of lift, flow and liquid delivery. The flow range of the delivered liquid is - L / s, the pressure range is .- MPa, and the diesel engine speed range is - rpm. Features: water pump, high automation and performance　　The specific treatment methods are as follows: first, whether the switch is tight, and whether the fuse is intact. In case of short circuit, short circuit, fuse burnout and other problems, it shall be repaired in time. If it is not a power problem, check the water pump　　However,LimassolDeep well submersible pump, that is, it takes some energy on the auxiliary impeller of the submersible slurry pump, which is generally about %. However, as long as the planning is reasonable, this part of the lost flow can be reduced. The slurry pump is mainly applicable to electric power, metallurgy and coalLimassol　　Vertical slurry pump is an early product. Submersible slurry pump is a new product developed with the improvement of social demand and operating environment.　　Second, the service life of the flow passage parts of the pump is relatively long, saving production costs.　　Function of shaft seal of submersible slurry pump: the main of shaft seal is to prevent high-pressure liquid from leaking out of the pump and prevent air from entering the pump.