MalapiHow much is Beijing Yijing steel bar turning softwareWhat role can it help you

With the development of steel structure buildings, only I-beam is not enough, that is, thickened I-beam, which is easy to lose stability for load-bearing columns. Direct rolling pass system. The direct rolling pass system refers to the pass system in which the two open legs of the I-beam pass are on the same side of the roll axis at the same time, and the waist is parallel to the roll axis.Malapi,Galvanized; hot-rolling;The side length of I-beam is small and the height is large, so it can only bear the force in one direction.Singapore,Methods of exerting efficiency in application of C-section steelThe specification of pass design I-beam is expressed in cm of waist width. For example, the waist width of No. I-beam is. The types of I-beam include hot-rolled ordinary I-beam, light I-beam and wide parallel leg I-beam (H-beam). The waist width of hot-rolled ordinary I-beam in China is ~, and the inclination of inner wall of leg is : The pass system of rolled I-beam includes direct pass system, cross pass system and mixed pass system. In addition,MalapiSquare rectangular hot dip galvanized welded pipe, I-beam can also adopt special rolling method.The general alloy pipe with improved performance is variable and has high application value. The alloy pipe contains more Cr and is heat resistant Low temperature resistance Corrosion resistance. There is no aluminum alloy in plain carbon seamless steel pipe, not very little aluminum alloy, and the alloy pipe is used in crude oil Aerospace Chemical plant Power engineering heating furnace. Because the physical properties of alloy tubes are easy to change and adjust.

Advantages of using I-beam: reduce maintenance cost, reduce downtime improve equipment operation rate,MalapiHow much is galvanized pipe DN65 per meter, reduce wear, reduce equipment capacity and increase power consumptionThere are many types of galvanized pipes, mainly including cold plated seamless pipes and hot-plated seamless pipes. But now the previous one is no longer used. The hot-dip seamless tube is still in use. Hot dip galvanized pipe is mainly used for steel pipes with low pressure fluid such as water and gas. When in use, if in normal working environment, the thickness of galvanized layer of hot-dip galvanized seamless steel pipe is up to μ M above, when purchasing, we should also find regular manufacturers to order. Only in this way can we achieve this service life. As long as the galvanized pipe is cleaned after pickling, it is basically cleaned in ammonium chloride or zinc chloride aqueous solution or ammonium chloride and zinc chloride mixed aqueous solution tank. In order to ensure the quality, electro galvanizing will not be used. There are also some small enterprises in the market. They will use electro galvanizing in production. In this way, although it is much cheaper in price. However, the quality is very good when used, house construction and building decoration. Its fracture will always be found in the production, manufacturing and key marketing of alloy pipe, That is,At present, there is still a big gap in the production technology of C-section steel between China and foreign countries.Whether I-section steel is ordinary or light, due to the relatively high and narrow section size, there is a large difference in the moment of inertia between the two main sleeves of the section. Therefore, it can only be directly used for members bent in the plane of their web or form lattice stress members. It is not suitable for axial compression members or members with bending perpendicular to the web plane, which makes it very limited in the scope of application.Stages needing attention in the production and manufacture of alloy tubes

Cold extrusion. This kind of processing method is more purposeful. Before the preparation of steel processing and extrusion molding when the extrusion molding is used for mm diameter pipe fittings, the investment of machinery and equipment is less, so the raw material consumption is also very small, and the technology is relatively perfect. Once the tube size is increased, the cold extrusion method must have large cargo capacity and high-power machinery and equipment. Therefore, the automatic control system will be upgraded.Job description,In order to make the steel pipe workpiece have the required mechanical, physical and chemical properties, in addition to the reasonable selection of materials and forming processes, heat treatment process is often essential. Steel is the most widely used material in the mechanical industry. The microstructure of steel is complex and can be controlled by heat treatment. Therefore, the heat treatment of steel is the main content of metal heat treatment. In addition, aluminum, copper, magnesium, titanium and their alloys can also change their mechanical, physical and chemical properties through heat treatment to obtain different service properties.The laying of reinforcement mesh can speed up the construction speed and shorten the construction period. In order to reduce the impact of construction on road traffic, the reinforcement and maintenance works of the two bridges are expected to be completed in the middle of next month.The flange of H-beam is of equal thickness, including rolling section and combined section composed of three plates welded. All I-beams are rolled sections. Due to poor production technology, a group of vertical rolls must be added for rolling at the same time. Therefore, its rolling process and equipment are more complex than ordinary rolling mills. The maximum height of rolled H-section steel that can be produced in China is mm, which exceeds the welded composite section.Malapi,I-beam is mainly used in building structure, curtain wall engineering, mechanical equipment and vehicle manufacturing.According to the national standard of hot rolled H-section steel in China (GB / t-, H-section steel is divided into narrow flange, wide flange and steel pile, whose codes are Hz, HK and Hu respectively. Narrow flange H-section steel is suitable for beams or compression bending members, while wide flange H-section steel and H-section steel piles are suitable for axial compression members or compression bending members. Compared with H-section steel, W IX and iy are not as good as H-section steel under the premise of equal weight.Last week, the billet in North China market showed a slight rebound trend. The billet quotation in Tangshan, the leading city, rose first and then stabilized in four trading days, with a strong wait-and-see atmosphere in the market. Affected by the almost stagnation of festival procurement, Tangshan billet fell by yuan during the Dragon Boat Festival holiday. On the first day after the festival, although the phase snail is still running at a low level, due to the small billet resources in the market,Malapi45 large diameter thick wall seamless pipe, the steel mills unexpectedly rose, and the billet market rebounded. However, due to the continuous increase of capital pressure and the downturn in the transaction of downstream finished materials the steel plant has always maintained a cautious wait-and-see attitude to maintain stability.