In this way, a smooth surface can be formed on the surface. Generally, the diving depth of the submersible slurry pump is not more than meters, and the operation is reliable. Why not more than meters? This is the crucial technical point of the submersible slurry pump, because the current sealing technology in China is more than meters, not because the slurry pump has a problem, but becauseVirginia Beach, In order to meet the use requirements of slurry pumps in different industrial fields and working conditions, we have continuously carried out research, development and improvement, so that we have different series, each series has a variety of specifications and models, and different series of products have different performance and s. Lets learn about it below A trash trap can be added at the position of the water inlet pipe and used at an angle of degrees, and then a filter screen is installed in the trap to filter impurities for the second time, so as to avoid the blockage of the submersible slurry pump during use.Le-Gros-Morne, Stop, then tighten the bearing seat, press down the nut, and fix the axial position of the rotor. The latter submersible slurry pump uses a barrel support, which generally does not need to adjust the impeller clearance. Therefore, if there is a problem with the clearance in the future use, loosen the support clamp first, and say that the nut is loose Submersible slurry pumps generally need to use some composite materials for manufacturing when they are used, so that they can have good wear and corrosion resistance when they are used and can be used to transport most of the media when they are used. Phreatic slurry There may also be mechanical failure of the pump, such as serious damage to the bearing of the pump, or the impeller will be stuck due to impurities such as water and grass when the pump pumps water
Discount. In order to meet the needs of industrial production and make the submersible pump to achieve the ideal use effect, accurate and reasonable selection is very important. In order to select the pump reasonably and correctly, the following aspects need to be considered: Selection of shaft seal form: shaft seal of submersible slurry pump Use a V insulation resistance meter to measure the insulation resistance between phases and phase to ground of the electric pump motor,Virginia BeachWater well pipeline pump, and the value shall not be less than m Ω. Otherwise, the motor stator winding shall be dried, and the drying temperature shall not exceed ℃. The operating environment is different: the key difference between the submersible slurry pump and the vertical slurry pump lies in diving. During the operation of the vertical slurry pump,Virginia BeachCirculating hot water pipeline pump, some parts intrude into the pit and cannot completely invade the slurry; The submersible slurry pump can completely penetrate below the slurry level.Job description, When the submersible slurry pump works, the pump needs to be placed on land, the suction pipe needs to be placed in water, and the pump needs to be started. Due to special structural requirements, when the slurry pump motor is submerged in the water, the slurry pump and submerged slurry circulating pump need to be placed above the water surface, so they need to be fixed, otherwise the motor will fall into the water According to the users requirements, the motor can add a variety of protection devices such as water inflow detection and overheating so that the product can operate safely for a long time under adverse working conditions. To repair the equipment. Submersible slurry pump is a machine used to transport liquid. It can be divided into many types according to different transport media. Then, when transporting some media with special properties, it is necessary to timely adjust the clearance between the impeller and the front guard plate. When adjusting the impeller clearance Impeller protection in order to ensure the operation of the submersible slurry pump, first stop the pump,Virginia BeachScrew deep well pump, loosen the bolts pressing the bearing box, make the bearing components move forward, and roll the shaft by hand to press the First, lets explain what kind of submersible sewage pumps WQ series and QW series refer to?. Next, the water seal, lock ring and other parts need to be installed.Virginia Beach, if the removed gasket is seriously damaged, a new gasket shall be replaced. The removed parts shall be cleaned with kerosene before assembly. The use of water pumps is related to all aspects of our life. With the arrival of the May Day holiday, the water consumption will increase. Therefore, it is necessary for us to choose a suitable water pump. All kinds of newly designed mechanical seals of submersible slurry pumps contribute greatly to the growth of market share.
lock 2022-06-30 09:46:49 support 0 | be opposed to 0
Sun Supply and Marketing Company 2022-06-30 11:51:19 support 0 | be opposed to 0
Mao Optical Co., Ltd. 2022-06-30 10:20:01 support 0 | be opposed to 0