HeranietzscheBaigang deep well pumpMore difficult to meet the needs of

　　 Precautions for disassembly of submersible slurry pump Before disassembling the filter press, make sure that the liquid in the submersible slurry pump is completely discharged. If the rotor is disassembled, drain the lubricating oil in the rotor bearing housing. If the newly added oil is stored,HeranietzscheDeep well pump, it should continue to be used after maintenance. Do not dump it directly　　 In addition, the use of ° and S-shaped bends should be reduced as much as possible during the installation and design of pipelines.Heranietzsche,　　 Store in a well ventilated and dry place. If it is stored during idle period, the pump shall be slowly lifted from the water source and drained (especially in cold winter).　　Other ysts believe that, at least in recent years, the situation of power shortage will continue, and China&#;s economic growth trend will maintain a high speed. Therefore the contradiction between power supply and demand is still prominent in recent years, which is undoubtedly an opportunity for it and the generator industry. In water pumps and generators, about % are used in concentrators in the mining industry. Due to the poor working conditions of primary ore dressing　　Some corrosive pastes containing crystals can also be transported. In the application range of slurry pump, different minerals, abrasion　　The vertical sand pumping pump is popular with a wide range of sand pumping pump users because it is easy to move. This equipment is made of high-tech endurance data. Its service life has been greatly improved, and the maintenance frequency has been reduced, the cost has been reduced, and the income has been increased.　　The seal cannot bear the water pressure at this depth. Once the water leaks, the motor will not work normally, resulting in damage to the submersible slurry pump. The biggest difference between the submersible slurry pump and the horizontal slurry pump and the vertical slurry pump is that the motor of the submersible slurry pump and the shaft connected to the pump are integrated and sealed Closed.

　　Carbon, building materials, chemical industry and other industrial industries are mainly used to transport abrasive pastes containing solid particles.　　At present, all screw pump manufacturers regard dry operation protection as a necessary unit for equipment procurement.　　If there are sundries blocked the pump will not be filled with water. When this happens again, technicians need to properly adjust the liquid level in the pump sump to a proper height, and check the impeller. In case of damage or aging, it needs to be replaced in time,device management,　　 Assembly of rotor parts of submersible slurry pump Before assembly, apply a layer of lubricating oil on the mounting surface to protect the shaft hole from damage.　　What stands out is the sealing of the container. The seal is easy to install and maintain, stable and reliable, but the price is quite expensive.　　The whole packing body,HeranietzscheBaigang deep well pump, including the packing gland,HeranietzscheWQ submersible sewage pump, packing ring and packing, needs to be disassembled; Submersible slurry pump Disassemble the o-seal ring, shaft sleeve, balance disc and key on the shaft in turn, and then the discharge section includes the last stage guide vane

　　; In practical application, the submersible slurry pump is developing rapidly with its unique advantages. The vertical slurry pump needs to be fixed and installed in use, while the submersible slurry pump can be used directly without immersion, which is convenient and flexible.management,　　In order to make the equipment perform better when it is used, but this also needs to be based on its working principle. It can not be adapted at will when it is optimized.　　Shaft seal water, no dilution of pulp, good shaft seal effect. It can be used when the slurry is not allowed to be diluted.　　 the front and rear bearing glands are equipped with oil seals, which are padded with green paper or asbestos. There is a gap of .- mm between the rear gland and the bearing.Heranietzsche, the motor temperature will rise, so it is easy to burn out the motor.　　Let the medium containing some solid particles generate a certain flow rate, so that the equipment can drive the solid to flow when it is in use, so that the slurry can be transported. In terms of the principle of the submersible slurry pump, it is actually quite simple