ColinDouble suction slurry pumpSubstantial damage to the industry

　　 Assembly of rotor parts of submersible slurry pump Before assembly, apply a layer of lubricating oil on the mounting surface to protect the shaft hole from damage.　　The premise of using this method is that the water gun must have sufficient flow during use, otherwise the effect of the submersible slurry pump may not be obvious.Colin,　　Transmission type: direct drive, parallel belt drive, upper and lower belt drive CV vertical belt drive, and can meet many kinds of harsh transportation conditions.　　For example etc. A variety of speeds and variants are adopted to make the pump operate under the best working conditions. It has long service life and high operation efficiency, concentrate and tailings are treated in the concentrator, ash and slag are removed from the power plant,ColinWQ submersible sewage pump, slime and dense medium coal are transported in the coal preparation plant, and slurry is transported in coastal river mining operations. The weight concentration of the treated slurry is: mortar %, ore slurry %; It can be operated in series according to the needs of users.Oduponkpehe,　　It will burn out. If there is a heating problem in use, you can refer to the following reasons.　　The submersible slurry pump shall be shut down for inspection in time in case of machine problems during operation, and regular maintenance shall be done. The equipment will not be used after burning out, which will cause certain economic losses to us.　　Submersible slurry pump it fills the gap in the application of slurry pump. When the submergence is deep and there is no good mud outlet, that is, the traditional slurry pump cannot be installed and operated, and the submersible slurry pump can supplement this part of the blank work point.

　　 Assembly of rotor parts of submersible slurry pump Before assembly, apply a layer of lubricating oil on the mounting surface to protect the shaft hole from damage.　　If there is no liquid in the cavity of the self-priming centrifugal pump of the submersible sewage pump,ColinHH slurry pump, the gas-liquid foam mixture cannot be formed and the air cannot be pumped. In order to ensure the speed and reliability of air extraction, sufficient liquid should be filled in the pump cavity before starting. What time would you like　　 The secondary pump shaft seal of the two-stage series pump is (packing seal), and the startup of the series pump also follows the above method. Only after the first stage pump is started, the submersible slurry pump can open the outlet valve of the last stage pump (the opening size is based on the motor current of the first stage pump as the rated powerManufacturing cost,　　Therefore, it is mainly because the installation will directly affect the use effect. The installation work should be seamless. Some key operating points can be seen when installing the slurry pump.　　The balance ring is also disassembled; Then remove the last stage impeller and the key back, and the middle section including the guide vane; in addition, remove the impellers, middle sections and guide vanes at other levels in the same way until the submerged slag slurry

　　What?Bidding,　　 Assembly of rotor parts of submersible slurry pump Before assembly, apply a layer of lubricating oil on the mounting surface to protect the shaft hole from damage.　　 Change the oil: if the oil contains water, drain it,ColinBooster pipeline pump, change the oil, and then tighten the screw plug.　　 one method is to use ultrasonic method to detect whether the equipment has cavitation. This method is often convenient for re detection. Even if there is some noise in the surrounding environment, many pumps tend to have better measurement results when in use.Colin,　　 add water with manual pump. Some pump owners have their own hand pumps. They can also buy or manufacture their own small hand pumps. The gate valve shall be installed at the water inlet. After closing the valve, inject a small amount of water into the water compressor to divert water. When the hand pump discharges water, it means that the pump is full　　Yes, summer is the peak sales season. In addition to agricultural applications industrial pumps have also increased in recent years.　　Screw it down, and then remove the bearing inner race, O-ring, shaft sleeve and retaining sleeve in turn.