FriedkSelf priming slurry pump wholesaleDocumentary on high quality development of material industry

　　Many users, including new practitioners of slurry pumps, often fail to distinguish the difference between submerged vertical slurry pumps and submerged slurry pumps. The names of submerged and submerged slurry pumps seem similar, but there are essential differences. What is the difference between submersible slurry pump and vertical slurry pump?　　 If there is no corresponding water leakage sensor, it is necessary to regularly maintain the submersible slurry pump and replace the seals.Friedk,　　QW (WQ) submersible non blocking sewage pump needs to be equipped with a fully active water pump control cabinet under no exceptional conditions. Do not directly connect the power grid or use the knife switch to connect the power supply to ensure the normal operation of the electric pump.　　We also need to limit the starting frequency and select appropriate thermal protection devices for use.Kotte,FriedkSplit vertical pipeline pump,　　Let the medium containing some solid particles generate a certain flow rate, so that the equipment can drive the solid to flow when it is in use, so that the slurry can be transported. In terms of the principle of the submersible slurry pump it is actually quite simple　　The seal cannot bear the water pressure at this depth. Once the water leaks, the motor will not work normally, resulting in damage to the submersible slurry pump. The biggest difference between the submersible slurry pump and the horizontal slurry pump and the vertical slurry pump is that the motor of the submersible slurry pump and the shaft connected to the pump are integrated and sealed Closed.　　 Why does the demand for submersible slurry pumps increase greatly? From the perspective of market demand, it has a rapid development momentum. The main reason is that the above-mentioned use is convenient and flexible; In addition, the application market of submersible slurry pump is also better than that of vertical pump

　　In addition, the sundries inside the pump body and impeller shall be cleaned. Then calibrate the pump shaft and motor shaft of the slurry pump to make them on the same horizontal line.　　The submersible sewage pump is mainly used to ensure various sewage pump products containing solid particles or other impurities. Because it works in water, we call it a submersible sewage pump, and the model selection of the submersible sewage pump is often determined according to the parameter information such as the nature and working characteristics of the sewage pump station.　　 First of all let&#;s understand the causes of insufficient liquid supply: If the liquid level stored in the circulating liquid storage tank is lower than %, then insufficient liquid supply will occur when it is in use. Or the pump adds too much lubricating oil, which leads to accumulationknowledge,　　During normal operation, the temperature of the motor is very high, it is easy to burn the motor and replace it with a new one. In fact, one motor burns out at this time. Don&#;t worry about replacing it. You must find out the cause of the motor&#;s heating, or　　 We must choose to consider the actual use situation when making the selection, because there will be some difference between the marked head when using and the head when using. This is because the pipe itself　　Work, no noise and vibration, and the site is cleaner.

　　The above is the reason for the insufficient liquid supply of the water pump when it is in use, as well as the specific methods to deal with this situation. We should pay attention to the regular inspection of the equipment during normal use to ensure that it is in useInstallation materials,　　Under the action of auxiliary devices,FriedkTwo stage slurry pump, it can transport the slurry, and because the sealing device itself is special, the moisture absorption section exceeds the suction section of the pump (the pump head is damaged). When the breathing tube passes through the pipe so that the pressure at both ends of the equipment can be balanced during normal use　　. Generally, the axial force cone tube shall be selected.　　 selection of flow: single suction pump or double suction pump shall be selected according to the flow; single suction pump or multi suction pump shall be selected according to the lift.Friedk,　　Adjustment. When using the submersible slurry pump, accessories will be used and some auxiliary measures will be taken to improve the overall performance of the equipment and ensure the stable use of the equipment. Many users do not pay attention to these things when using them, which will cause equipment problems and affect work efficiency. So we&#;re using　　The structure of the submersible slurry pump will be more intuitive. First, the equipment will use centrifugal force to drive the liquid from the impeller to the outer edge and obtain energy,FriedkWear resistant slurry pump, and then leave the edge of the impeller at a higher speed　　Submersible slurry pump In addition, it must be used continuously during transportation. If there is an interval in the middle, it must be avoided that the interval is relatively long, so as to avoid the solidification of slurry in the pump when the operation is stopped.