DanbicaElectric hydraulic fixed lifting platformOffice property enters the stock market

Staying below high-altitude work sites is prohibited, and safety nets or other protective devices should be installed below the work site to avoid injury from falling objects.Check the rollers, intermediate shafts, and bearings; Oil cylinder pin and bearing; Equality and wear of the hinge shaft and bearings of the boom; Add oil to the above components for maintenance of outdoor elevators and factory elevators. Extend the service life of bearings.Danbica,The correct use of hydraulic elevators can extend their service life and also play an important role. So how should they be used?When using the distribution box, the selection of the leakage switch should be compatible with the frequency converter.Slobozia,The seat belt needs to be inspected every six months, check whether the seat belt is broken or deformed, and keep records of the experiment. Any unqualified seat belts should be immediately stopped from use.The application scenarios of mobile elevators may require several or even dozens of passenger elevators in some office buildings and hospitals. In order to increase the speed, efficiency, and usable area of electric elevators, most high-rise buildings will divide electric elevators into arrays, with each group responsible for a portion of the floors, and make different adjustments and scheduling based on the usage mode of different floors at different times.Every month, it should be ensured to add butter twice to the transmission position where the grease nipple is located. For areas where butter cannot be added, it is necessary to clear the oil circuit or replace the grease nipple until butter can be added. Otherwise, it is prohibited to use the equipment.

Unique design; Work; The steel frame can withstand average pressure, effectively reducing the torsion of the frame, and has stronger durability.Check the one-way valve in the valve group for natural lowering of the lifting platform. If dirt is found on the sealing surface of a single valve, clean the one-way valve.Fault analysis of mobile elevators: Mobile elevators cannot lift or have weak lifting force: overflow valve pressure regulation does not meet the requirements: adjust the pressure to the required value; Oil cylinder internal leakage: check or exchange oil cylinder components; Clamping or internal leakage of directional valve: Check or exchange valve components; If the oil level is too low and the oil inlet filter is blocked, add enough oil and clean the filter. The fuel supply pump has drawbacks: check or exchange the pump.The cost is reasonable,The lifting force of the scarifier is not strong or the lifting force is weak: the pressure regulation of the overflow valve does not meet the need to adjust the pressure to the required value; Refer to cleaning item above for leakage in the oil cylinder; The directional valve is stuck or leaking internally; The oil level is too low, and the oil inlet filter is blocked; The fuel supply pump has drawbacks; Check the wear and tear of the one-way valve core and valve seat, and check if the one-way valve spring is tired or deformed.Maintain a smooth access road for external construction elevators and sufficient parking space for equipment. When using a crane for auxiliary installation, full consideration should be given to whether the on-site environment meets the operating conditions of the crane.The lifting platform has been inspected and debugged before leaving the factory, and all technical indicators meet the design requirements. When in use only the power supply needs to be connected, and the hydraulic and electrical systems basically do not need to be adjusted.

With the increasing demand for boarding bridges, mobile boarding bridge merchants are increasingly interested in using boarding bridges to provide customers with the appearance of hydraulic boarding bridges, and the demand for boarding bridges is also increasing. However, and they do not produce them themselves,DanbicaMicro hydraulic lifting platform, resulting in high prices. What is important is that they do not have a good understanding of the technology of car booths, and there are often deviations when passing on the technical requirements of direct customers to the manufacturers. Therefore, customers who purchase boarding bridges can directly find professional manufacturers. When choosing a boarding bridge,DanbicaIndoor hydraulic lifting platform, the first thing to consider is the range of use, frequency of work, utilization rated weight, and other factors of the product,DanbicaLifting hydraulic platform, and choose a boarding bridge that is suitable for the requirements of the unit. Conduct market research based on the proposed technical parameters. The first condition for selecting a supplier is to consider the manufacturer of the boarding axle, and then the after-sales service capability. As long as it is a fixed boarding bridge with good product quality excellent performance, and complete equipment, it can be chosen at a reasonable price.Customer first,The lifting force of the scarifier is not strong or the lifting force is weak: the pressure regulation of the overflow valve does not meet the need to adjust the pressure to the required value; Refer to cleaning item above for leakage in the oil cylinder; The directional valve is stuck or leaking internally; The oil level is too low, and the oil inlet filter is blocked; The fuel supply pump has drawbacks; Check the wear and tear of the one-way valve core and valve seat, and check if the one-way valve spring is tired or deformed.Hydraulic pump station: domestic lifting platform dedicated pump station, Italian imported pump station with external protective devices: organ m type, mesh type, and iron plate sealed type.Regular inspection and maintenance, eliminating hidden dangers, extending equipment service life, and ensuring the safety performance of elevators.Danbica,Although lifting cargo elevators have good safety, in practical work, if we do not pay attention to detailed maintenance, accidents may occur. Therefore, we should pay attention to them when performing daily maintenance.Firstly, it is necessary to use and operate the elevator correctly. The operators should receive systematic operation training: regular inspection of operating standards should be carried out, and any violations of elevator operation should be detectedThe main structure and purpose of a guide rail elevator: The mechanical part of a guide rail elevator mainly includes three parts: a lifting device, a track device, and a belt changing device. The lifting device is mainly used to suspend the person being lifted, which is the core part of the entire mechanism. The track device is mainly used to provide movement trajectory, making operation more smooth. The belt changing device is used to switch tracks when the elevator is about to pass through a door. The internal structure of the lifting device is mainly composed of gear mechanism, bracket, worm gear, guide mechanism, lifting arm upper and lower shells, etc. The gear mechanism mainly includes large and small gears, winding pulleys, central shafts, and safety devices composed of stop buckles and torsion springs.