Cage wooden boxHow much is Q345B I-beam per tonThe impact of equipment performance

The specification of pass design I-beam is expressed in cm of waist width. For example, the waist width of No. I-beam is. The types of I-beam include hot-rolled ordinary I-beam, light I-beam and wide parallel leg I-beam (H-beam). The waist width of hot-rolled ordinary I-beam in China is ~, expressed as No. ~ No., and the inclination of inner wall of leg is : The pass system of rolled I-beam includes direct pass system, cross pass system and mixed pass system. In addition, I-beam can also adopt special rolling method.I-beam is widely usedCage wooden box,In view of the current market environment, especially in terms of construction or equipment manufacturing technology, the position of galvanized pipe is still relatively large. It is precisely because of this strong position that we can see this kind of building material in all walks of life, even in a field that seems to have little contact. It will be applied in many construction projects. At the same time, even in the depressed environment of the steel industry, the application situation and utilization rate of this kind of pipe are very high.Key technical characteristics of alloy pipe:ViljoenskroonGenerally, there are many passivation methods for alloy tubes the common ones are high temperature passivation or sodium cyanide passivation.I-beam is a long strip steel with groove section, which belongs to carbon structural steel for construction and machinery. It is a section steel with complex section, and its section shape is groove shape. China&#;s imports of I-beams are greater than its exports. The main producing areas are Tangshan Iron and steel, Baotou Iron and steel, Shangang, huangte, Maanshan Iron and steel, Xuanhua Iron and steel, Japan iron and steel, etc.I-beam is divided into ordinary I-beam and light I-beam. The specification of hot rolled ordinary I-beam is -#. The specification of hot-rolled flexible I-beam supplied through agreement between the supplier and the buyer is -#. I-beam is mainly used in building structure, other industrial structures and fixed panels and cabinets. I-beam is often used together with I-beam.

Dry processing technology: after passivation treatment, parts shall be dried with air compression or hot gas, or drying treatment or air drying can be selected.From the situation of chiseling on site, the reinforcement mesh laid by the construction party is cm below the surface layer, which greatly exceeds the specification, and then the crack resistance of the reinforcement mesh can be reduced. Because of the increasing temperature, the effect of thermal expansion and cold shrinkage and the characteristics of concrete, the cracking of surface layer is significant.Ways to obtain surface compressive stress characteristics of alloy tubesmanufacturer,The finished product has smooth surface,Cage wooden boxSteel pipe, low friction coefficient flatness error + / - mm / m length, wear resistance and maximum temperature of ℃The wear resistance, impact toughness and bending strength under different process conditions were compared, matching test with lubricating grease and user test, it is proved that ZYS- bearing damping and antirust oil has outstanding damping effect and good antirust lubrication performance.X-ray or ultrasonic testing shall be carried out for repair welding of alloy pipe, dead end welding of strip steel and circumferential seam. For the spiral welding of steel for the transportation of flammable general liquids, yibai%sx ray or ultrasonic testing shall be carried out. For the spiral welding of alloy pipes for the transportation of water, wastewater, gas, heating steam and other general liquids, X-ray or ultrasonic testing sampling inspection (%) shall be carried out.

All the cracks occur at -mm away from the edge below the alloy pipe, and the macroeconomic orientation is vertical to the cold rolling orientation, showing a 'high mountain' shape.Test results,Methods of exerting efficiency in application of C-section steel Completion of pipeline trench ground; Bricklaying of pipe shaft is completed. Direct rolling pass system. The direct rolling pass system refers to the pass system in which the two open legs of the I-beam pass are on the same side of the roll axis at the same time, and the waist is parallel to the roll axis.Cage wooden box,Cage wooden boxHow much is No. 16 I-beam per ton,The crack mainly occurs at -mm from the edge of the alloy pipe. The shape is several parallel vertical cracks of different sizes. The regularity is that the thicker the specification and model of the alloy pipe is The wider the width, the more serious the disadvantages.According to the national standard of hot rolled H-section steel in China (GB / t-, H-section steel is divided into narrow flange, wide flange and steel pile, whose codes are Hz,Cage wooden box15CrMoG seamless alloy pipe, HK and Hu respectively. Narrow flange H-section steel is suitable for beams or compression bending members, while wide flange H-section steel and H-section steel piles are suitable for axial compression members or compression bending members. Compared with H-section steel, W, IX and iy are not as good as H-section steel under the premise of equal weight.When selecting I-beam in structural design reasonable I-beam shall be selected according to its mechanical properties, weldability and structural size.