I-beam is mainly divided into ordinary I-beam, light I-beam and wide flange I-beam. According to the height ratio of flange to web, it is divided into wide, medium and narrow flange I-beams. The specifications of the first two are -, that is, the corresponding height is -. At the same height, the light I-beam has narrow flange, thin web and light weight. Wide flange I-beam, also known as H-beam, is characterized by two parallel legs and no inclination on the inner side of the legs. It belongs to economic section steel and is rolled on four high universal mill, so it is also called 'universal I-beam'. Ordinary I-beam and light I-beam have formed national standards.The grid spacing size and number of reinforcement of electric welding reinforcement mesh are correct, which overcomes the phenomenon of large spacing size error and missing binding and buckle of binding quality caused by manual placement of reinforcement in traditional manual binding. The welded steel mesh has high strength and good elasticity. When pouring concrete, the steel bar is not easy to be partially bent and does not change. Because it is considered that the longitudinal and transverse steel bars are spot welded into a mesh structure, so as to achieve the goal of side-by-side average stress and bonding anchor.Key technical characteristics of alloy pipeQuotation sheet,Alloy pipe is a spiral seam seamless steel pipe which is made of hot-rolled strip steel coil, often processed by warm extrusion and welded by automatic double wire double side arc welding process. The alloy pipe sends the hot-rolled strip steel to the welded pipe unit, and the hot-rolled strip steel is extruded through multiple passes. The hot-rolled strip steel is rolled slowly to produce annular pipe material with open mouth gap. Adjust the reduction amount of the extrusion roll to control the welding gap at ~ mm and make both sides of the weld flush.I-beam can only be used for beam, while H-beam can be used for load-bearing column of structure.I-beam has the dual properties of high hardness and toughness materials. Compared with other engineering wear-resistant materials in China, such as various alloy steel plates, cast wear-resistant plates, cast stones, rubber, polyurethane, etc., it has irreplaceable comprehensive excellent properties.
Alloy pipe is a spiral seam seamless steel pipe, which is made of hot-rolled strip steel coil, often processed by warm extrusion and welded by automatic double wire double side arc welding process. The alloy pipe sends the hot-rolled strip steel to the welded pipe unit, and the hot-rolled strip steel is extruded through multiple passes. The hot-rolled strip steel is rolled slowly to produce annular pipe material with open mouth gap. Adjust the reduction amount of the extrusion roll to control the welding gap at ~ mm and make both sides of the weld flush.Workshop cost,Defects of alloy pipe and solutions: According to the purpose, the welded pipe has general purpose and high temperature and high pressure. The pipe used in the latter is often special alloy steel. The problem of shrinkage cracks in the welding process and the mechanical properties of the pipe in the heat affected zone must be considered and solved and the mechanical properties of the pipe in the heat affected zone will not be greatly changed due to the influence of welding operation.→ compared with the concrete structure, the I-steel structure can increase the service area by %, reduce the self weight of the structure by % - %, and reduce the structural design internal force.vertical,Plan option : Martensitic chromium alloy pipe,Nitriding: also known as nitriding, it is the process of penetrating nitrogen atoms into the surface layer of steel. At present, gas nitriding is widely used in the production of alloy steel pipe.The high-temperature passivation treatment of alloy pipe is to obtain the passivation treatment film by heating in the heat treatment equipment. Before passivation treatment, the surface layer of parts must be removed to remove waste. At a higher temperature, the passivation treatment film can be obtained according to the transformation temperature and time. The hue of passivation treatment film can refer to the annealing color of alloy pipe, and the main parameters of ambient temperature and time of heat treatment process can be selected.
agricultural tourism 2022-06-09 23:00:09 support 0 | be opposed to 0
loading machinery 2022-06-09 21:08:15 support 0 | be opposed to 0
Minor Trading Company 2022-06-09 20:55:45 support 0 | be opposed to 0