MetkovicHorizontal slurry pumpWord of mouth recommendation

　　 Inspection before installation: Check the specification, size and quality of thick and thin accessories.　　Pressure. Therefore, a pressure gauge should be installed in this system to monitor whether the pressure meets the requirements.Metkovic,　　Stainless steel deep well pump is not a disposable product,MetkovicVertical centrifugal slurry pump, nor a short-term product but a long-term equipment. One investment can ensure long-term profits, if there are some small problems and there is no need to replace equipment in a short time. Moreover, it is very easy to maintain, and the maintenance work will not be too difficult. therefore　　First, let&#;s talk about the familiar vertical slurry pumps. Here we refer to ZJL and SP submerged slurry pumps. Strictly speaking, the submersible slurry pump is also a vertical slurry pump, because its axis is basically vertical when it works, but it can be completely immersed in water when it runs so it is a good choiceEl Fahs,　　Different process requirements: the motor used in the vertical slurry pump is an ordinary vertical motor, which has no waterproof . The motor of the submersible slurry pump and the pump shaft are coaxial. The motor shall be waterproof and sealed. The motor and the pump body can invade underwater at the same time.　　What is the solution to this situation?　　Many users, including new practitioners of slurry pumps, often fail to distinguish the difference between submerged vertical slurry pumps and submerged slurry pumps. The names of submerged and submerged slurry pumps seem similar, but there are essential differences. What is the difference between submersible slurry pump and vertical slurry pump?

　　The hardened mud layer collapses after softening, avoiding the phenomenon of burying the pump during use.　　Will it be damaged by underground humus and hot water? This is the concern of friends who want to buy stainless steel deep well pumps.　　Extend service life. In fact, the submersible slurry pump is widely used in many lives, and there is a very important component water seal in the pump, so it mainly plays a role in useWord of mouth recommendation,　　 Dust and oil stains on the motor reduce the heat dissipation capacity of the equipment and cause the equipment temperature to rise.　　It is not correct that it has no effect on us.　　 When stopping the operation of the submersible slurry pump, close the cock of the vacuum gauge and pressure gauge and the gate valve on the water outlet pipeline, and After that, cut off the power supply of the motor. If the temperature of the environment is low, open the square plug at the lower part of the pump body to remove the remaining water to avoid frost cracking. During operation, the maximum temperature of the bearing shall not exceed ℃, and the quantity of calcium base grease used for lubricating oil bearing shall be the same as that of the bearing body

　　Friction. Because if the surface of the pump is smooth when it is used, the submersible slurry pump and impeller are sprayed with polymer composite materials for useAdministration,　　 A trash trap can be added at the position of the water inlet pipe and used at an angle of degrees, and then a filter screen is installed in the trap to filter impurities for the second time, so as to avoid the blockage of the submersible slurry pump during use.　　The lift of deep well pump is calculated according to the following formula　　 Dust and oil stains on the motor reduce the heat dissipation capacity of the equipment and cause the equipment temperature to rise.Metkovic,　　 First, screw down the bolts on the side bearing pressure cap, and then remove the nuts used for the connection between the three parts: discharge section,MetkovicBooster pipeline pump, and successively install the bearing inner race, bearing gland and retaining sleeve　　Avoid airborne sound transmission; Ensure the airtightness of machine room doors and windows. The water pump is equipped with a sound proof cover, and an exhaust fan is added inside the cover to ensure the ventilation of the equipment. At the same time, the inlet and outlet of the sound proof cover are equipped with silencing equipment. A vibration isolation platform is installed at the bottom of the water pump for foundation vibration reduction to isolate the vibration generated during the operation of the water pump　　 The standby submersible slurry pump shall roll the shaft / turn every week to make the bearing uniformly accept the static load and external oscillation. The building structure in the water pump room shall be reconstructed. Sound absorbing and isolating plates shall be installed around the wall and on the top of the machine room and fixed with light steel keel; The connecting holes between the machine room and other rooms are tightly blocked,