HanoverWQ submersible pump parametersFilling materials for the industry

　　Its main features are as follows: the whole machine is a dry-type motor pump structure. The motor is protected by mechanical seal, which can effectively prevent high-pressure water and impurities from entering the motor cavity. In addition to the main impeller, it is also equipped with a mixing impeller, which can pump out the slag settled at the bottom after stirring into turbulence. impeller　　So it is called: submersible slurry pump.Hanover,　　Dynamic water level: after the pump operates normally, the water inflow in the pool and the pumping capacity of the deep well pump reach an equilibrium point, and the water level at this time is called dynamic water level.　　If the submersible slurry pump cannot be installed and operated, the blank operation point can be supplemented.Xanthi,　　The impeller of the submersible slurry pump may need to be disassembled for maintenance or repair during use. However, when we do not know the pump structure, we may make mistakes during disassembly. Let&#;s take a look at the correct disassembly of the impeller　　If the water leakage is serious, the broken pipe shall be dismantled and replaced. Lower the lift and press the nozzle of the water pump into the water for .m.　　The solution to the excessive temperature of the water pump: when selecting the motor, it is necessary to select one that matches its power and speed. In addition, the cooling fan should be installed on the main shaft. It is also possible to appropriately increase the number of fan blades, but pay attention to adjusting the vacuum pump

　　After that, before starting again, check whether the impeller rolling is normal and whether the bearing assembly compression bolts are tightened, and then start the pump.　　Some protection s are beyond the reach of manual operation.　　 Why does the demand for submersible slurry pumps increase greatly? From the perspective of market demand, although the number of submersible slurry pumps has not exceeded that of vertical slurry pumps,HanoverBaigang deep well pump, the application market of submersible slurry pump is also better than that of vertical pumpmarket price,　　Pump. In addition, the submersible slurry pump is mainly characterized by 'slurry',HanoverWater well pipeline pump, bearing puller (commonly known as triangle puller), magnetic dial indicator, outside micrometer, caliper, feeler gauge, square ruler, copper bar, screwdriver with handle, hammer, V-shaped irons of the same specification, clean kerosene, cotton yarn, etc.　　Submersible slurry pump is a kind of pump used in mines. Do you know the effect and form of its shaft seal? Let&#;s have a look.

　　 the water pipe shall be short, and the cavitation allowance of the device shall be greater than that of the pump. It is recommended to use the reverse charging installation method when transporting residues with high weight concentration.plan,　　A large amount of lubricating oil is stored.　　 Check whether there is a problem with the ventilation system: check whether the fan is damaged, whether the fan rotates correctly, and whether there are abnormal objects blocking the ventilation holes.　　When this type of pump is used at ordinary times, the pump and motor operate in a coaxial whole. When it runs, the motor shaft will drive the impeller of the pump to rotate,HanoverAh slurry pump, and then at this time the rotating force can be brought to the medium,　　Slurry pump Inappropriate model is selected when selecting the pump. In actual use so thatHanover, when the load conditions do not match the model of the slurry pump, for example, the pump lift used is too high or too low, which will lead to overload, so we are selecting the pump　　 If it is found that the impeller is damaged and the liquid supply is insufficient, it is necessary to replace the new impeller in time for use.　　Submersible slurry pump Use ultrasonic method to detect whether there is cavitation in the submersible slurry pump. This method is often convenient for re detection. Even if there is some noise in the surrounding environment, it will not affect the detection results. Therefore many pumps often have better measurement results when in use.