TucsonIrrigation deep well pumpHeating problem solution

　　 Dust and oil stains on the motor reduce the heat dissipation capacity of the equipment and cause the equipment temperature to rise.　　Water pump After understanding the cause of insufficient liquid supply we need to check whether the liquid level of the circulating liquid storage tank needs to add media to it.Tucson, chemical industry, paper mills, timber, restaurants, textiles, bathrooms, hotels and other departments. The operating temperature is generally not more than ℃.　　Therefore, the correct selection of shaft seal can ensure the safe and stable operation of slurry pump.Kolomyya,　　It is located in the middle, so it seems that many regions have good effects when using it.　　 Next, it is necessary to check the water seal. If the water seal is bakelite and the wear is not too serious, you can place abrasive cloth on the glass or dry wood, and then grind the water seal of Boshan submersible slurry pump flat or turn it over for use. However, if the thrust rubber water seal is used when　　.

　　Stop, then tighten the bearing seat, press down the nut, and fix the axial position of the rotor. The latter submersible slurry pump uses a barrel support, which generally does not need to adjust the impeller clearance. Therefore, if there is a problem with the clearance in the future use, loosen the support clamp first, and say that the nut is loose　　The treatment methods are as follows: Check whether the current and voltage of the water pump are abnormal at this time. If the current is obviously reduced, for example, it is only half or a little more than normal,TucsonHH slurry pump, it may be that the impeller is worn or the check valve is blocked. If the current is not much different from the normal current,TucsonWQ submersible pump parameters, it can be　　Ordinary vertical motor can be used without waterproof, while the motor shaft and pump shaft of submersible slurry pump are coaxial, so the motor must be waterproof and sealed, and the motor and pump can be immersed in liquid at the same time; The vertical slurry pump is an early product, and the submersible slurry pump is a newly developed product according to the market demandQuality department,　　Ensure that the service time will be extended when it is used. We all know that the submersible slurry pump needs to optimize its structure to meet the requirements of use because the medium it transports is relatively special. The structure has been optimized to　　Discount. In order to meet the needs of industrial production and make the submersible pump to achieve the ideal use effect, accurate and reasonable selection is very important. In order to select the pump reasonably and correctly, the following aspects need to be considered: Selection of shaft seal form: shaft seal of submersible slurry pump　　There are differences.

　　The whole packing body, packing ring and packing, needs to be disassembled; Submersible slurry pump Disassemble the o-seal ring, balance disc and key on the shaft in turn,　　In the application of pumps, the first thing we think of is water. Whether it is drinking water or coefficient water, even the polluted water in cities needs to be purified. All these require its equipment to provide services for us. Without pumps, our basic survival is a problem.　　 After one year of use, check the corrosion of the pump,TucsonSplit vertical pipeline pump, remove the rust and paint. If the submersible pump is not used for a long time, it should be carefully checked and put dry.　　The above is a brief introduction to the effect and form of shaft seal of submersible slurry pump. Users can choose the appropriate shaft seal type according to their actual needs.Tucson,　　 During the installation of smooth bearing components, if the installation is correct, the smooth oil is appropriate, the repair is timely, and the delivery life will be long, the repair personnel should regularly repair the bearing components, check the condition of the bearings and the smooth oil, and regularly add or replace the smooth oil during the work, and the interval and write　　If the pressure in the local area is equal to or lower than the vaporization pressure corresponding to the water temperature in the flow process, the water will vaporize there and form many small bubbles mixed by steam and gas. The cavitation phenomenon is due to the bubble action when these small bubbles flow from the low-pressure area to the high-pressure area in the water pump,　　To repair the equipment. Submersible slurry pump is a machine used to transport liquid. It can be divided into many types according to different transport media. Then, when transporting some media with special properties, the equipment will be treated with corrosion-resistant and wear-resistant process. Only in this way can the equipment be improved