BlanickSelf priming slurry pump wholesaleVarious value materials

　　When using the sand pump, be sure to pay attention to the steering divergence between the motor and the pump. The sand pump has an arrow on the pump to mark the main steering. After the power supply is connected,BlanickLong shaft submerged slurry pump, run the pump without load. Check whether the motor operates normally. During operation be careful not to exceed the bearing on the pump support to avoid　　Under the action of auxiliary devices, it can transport the slurry, so that the pressure at both ends of the equipment can be balanced during normal useBlanick,　　The sand suction pump and sand water separator in the aeration grit chamber of the screw pump operation pre-processing unit are used to remove the sand particles in the sewage. It is necessary to ensure their normal operation,BlanickHorizontal wear-resistant slurry pump, so as to reduce the sand particles in the sludge and prolong the service life of the screw pump.　　 First, screw down the bolts on the side bearing pressure cap and then remove the nuts used for the connection between the three parts: discharge section, stuffing box body and bearing body; Then screw off the round nut on the shaft, and successively install the bearing inner race, bearing gland and retaining sleeveShahr-e Kord,　　In the application of pumps, the first thing we think of is water. Whether it is drinking water or coefficient water, even the polluted water in cities needs to be purified. All these require its equipment to provide services for us. Without pumps, our basic survival is a problem.　　In addition to the main impeller inside the equipment, a set of impeller for mixing will be added at the bottom of the equipment, so that some mortar slowly settled inside the equipment can be mixed with water to become a flowing medium, so that the equipment can be used without its　　According to the user&#;s requirements, the motor can add a variety of protection devices such as water inflow detection and overheating, so that the product can operate safely for a long time under adverse working conditions.

　　 Then reinstall the equipment on the engine and install the rubber hose.　　 Check the water pump: it is possible that the selection of the water pump is not matched with the motor, which makes the temperature of the motor too high after long-term operation; It is also possible that the working time exceeds the specified working time of the motor. At this time, the use time and times should be strictly limited, the correct thermal protection should be selected, and　　 fold the three layers in half with self-adhesive butyl tape and gradually extend to the outside of the core. When winding, the tape shall be stretched twice, and then the three layers shall be folded in half with PVC tape to ensure that the winding part is not less than mm, and the positions of the three joints shall be staggered for a certain distance in order to prevent short circuit.packing,　　Therefore, the stator winding will be burnt out due to excessive temperature rise.　　What is the order.　　 During the installation of smooth bearing components,BlanickQuotation slurry pump, if the installation is correct, the smooth oil is appropriate, the repair is timely, and the delivery life will be long, the repair personnel should regularly repair the bearing components, check the condition of the bearings and the smooth oil, and regularly add or replace the smooth oil during the work, and the interval and write

　　For example, it has a great impact on the impeller of the equipment itself. So how to detect whether the equipment has cavitation during use?Highly recommended,　　 Precautions for disassembly of submersible slurry pump Before disassembling the filter press, make sure that the liquid in the submersible slurry pump is completely discharged. If the rotor is disassembled, drain the lubricating oil in the rotor bearing housing. If the newly added oil is stored, it should continue to be used after maintenance. Do not dump it directly　　 There are many reasons for motor overheating. It may be because the power supply voltage is too high or there is a problem with the water pump or the motor itself.　　Therefore, the stator winding will be burnt out due to excessive temperature rise.Blanick,　　The supply of shaft seal water must be ensured. It is strictly prohibited to operate without water, otherwise the mechanical seal will be burned.　　The hardened mud layer collapses after softening, avoiding the phenomenon of burying the pump during use.　　 Before starting the submersible slurry pump, the rotor of the rotating pump shall be smooth and even, and water shall be injected into the pump to ensure that the pump is full of water without air.