GiljaRed copper barLeveraging the market

Some steel mills in Liaoning are interested in purchasing pig iron, and the iron mills quotations are on the high side, resulting in a stalemate between supply and demand. The demand for cast iron and ductile iron in Jiangsu, Shandong, Shanxi, Hebei, Henan and other regions is sluggish, and the inventory pressure of iron mills is increasing. As the price of raw materials decreases, the quotation of iron mills continues to decline. At present, the demand and cost support are weak, and there is no positive boost. The short-term pig iron market is weak and difficult to change.The simplest way is to use copper cleaner. Brass, red copper, bronze, etc. can be used. Oil stains, fingerprints, oxide layers, etc. on the surface can be cleaned with copper cleaner first.Gilja,Copper pipe corrosion caused by soft water.Remove the flame. If the filler metal does not melt, continue to heat the joint and try again. The melted filler metal is sucked into the casing port according to the capillary effect until a complete filler metal ring appears on the casing port. Remove the flame Pay special attention not to let the flame directly contact the filler metal. It should be the heat at the joint that melts the filler metal. In order to clean the copper pipe, the welding flux must have a degree of corrosivity, and shall be cleaned after brazing. The so-called & quot; self-cleaning& quot; fluxes are generally not recommended because of their corrosivity.Sundbyberg,Extrusion method: This production method is to cast copper ingots after smelting, and extrude copper tubes by large extruder after secondary heating.The conductive production of copper tube is the latest method for this method. It is the production of nanocrystalline copper materials with conductivity. Because this raw material is very special, it is a copper material produced by using nanotechnology, and copper ions can be separated by conductivity, so that copper tubes can be produced with the separated copper ions. This method is very complex, requires high technology and new equipment, so only advanced foreign countries can use this production method.For small diameter pipes, when using filler metal, the length of filler metal is allowed to be equal to the diameter of the pipe, which is enough to fill the weld crater. One of the five major application fields of red coppr plate T, red copper bar and red copper tube: copper is the most widely used and used in the electrical and electronic industries, accounting for more than half of the total consumption. Used for various cables and wires, motors and transformers, switches and printed circuit boards; In the manufacture of machinery and transport vehicles, it is used to manufacture industrial valves and accessories, instruments, sliding bearings, heat exchangers, pumps, etc.

At the opening this morning, the market price of Zhengzhou copper bar was basically stable. According to the monitoring data of the Lange cloud business platform the current market price of * mm Linyi copper bar was yuan (ton price, the same below), the * mm copper bar was yuan, steel mills in some northern cities implemented production restriction, and some domestic economic data improved, which boosted manufacturers confidence. Today, steel prices generally rose. However, the construction progress of the downstream construction site is affected, which is not conducive to the continuous demand. The high spot price transaction today is weak, which is difficult to support the continuous rise of steel prices. It is expected that the building materials market will maintain a volatile trend tomorrow, and some businesses may reduce prices and take goods.new product,Although the opening continued the weak trend, the intraday transactions improved, and the prices of some copper bar manufacturers rose. From the specific situation although the manufacturer feedback that the shipment is average, the mentality is relatively calm, and the manufacturer is not willing to significantly reduce the price. In terms of the market, the transaction of strip steel is better than other steel varieties, the overall demand for strip steel remains in a good state.Copper pipe has the characteristics of, and is the choice for the installation of water pipe, heat supply and refrigeration pipe.The application of copper tube The copper tube is generally used in the heat exchange equipment, and the low-temperature pipeline in the oxygen production equipment can also be used. Some relatively thin copper tubes can be used to transport some pressurized liquids, and can also be used as pressure measuring tubes in instruments; In addition, the copper pipe is relatively firm, unlike other metals, which are easily corroded, so now many water pipes and refrigeration pipes used in buildings will choose to use the copper pipe.

For small diameter pipes, when using filler metal, the length of filler metal is allowed to be equal to the diameter of the pipe, which is enough to fill the weld crater. One of the five major application fields of red coppr plate T red copper bar and red copper tube: copper is the most widely used and used in the electrical and electronic industries, accounting for more than half of the total consumption. Used for various cables and wires, motors and transformers, switches and printed circuit boards; In the manufacture of machinery and transport vehicles, it is used to manufacture industrial valves and accessories, instruments, sliding bearings molds, heat exchangers, pumps, etc.knowledge,The room temperature tensile strength of the annealed red copper sheet is ~ kgf/mm, the elongation is ~%, and the Brinell hardness (HB) is ~Standardize production.When welding, just add enough filler metal to fill the capillary gap. Too much filler metal will only form a ball at the bottom of the joint or run into the pipe.Gilja,Save materials and total cost, stability and performance, and can save maintenance.So far as the storage method of copper materials is concerned, we should properly keep the copper products we buy, extend the service life of copper and ensure its performance to avoid unnecessary losses.The hard copper tube is not artificially treated after being drawn or extruded so that it can be naturally formed. At this time, the organizational form in the copper tube is full. This kind of copper tube is more likely to crack and is not suitable for bending. Therefore, the hard copper tube is generally straight.