ArkarnsWater well pipeline pumpKnowledge of processing and maintenance

　　When the submersible slurry pump works the pump needs to be placed on land,ArkarnsRubber lining submerged slurry pump, the suction pipe needs to be placed in water, and the pump needs to be started. Due to special structural requirements, when the slurry pump motor is submerged in the water, the slurry pump and submerged slurry circulating pump need to be placed above the water surface so they need to be fixed, otherwise the motor will fall into the water　　If there are sundries blocked, the pump will not be filled with water. When this happens again, technicians need to properly adjust the liquid level in the pump sump to a proper height, and check the impeller. In case of damage or aging,Arkarns,　　The deep well pump works underwater. Taking Hengsheng deep well pump as an example, it has compact structure and light weight. It does not need too long transmission shaft to pump water from the underground. Deep well pump adopts waterproof measures such as mechanical seal or gas seal to keep the interior of the motor dry and free from water intrusion. Hengsheng pump today　　Many users, including new practitioners of slurry pumps often fail to distinguish the difference between submerged vertical slurry pumps and submerged slurry pumps. The names of submerged and submerged slurry pumps seem similar, but there are essential differences. What is the difference between submersible slurry pump and vertical slurry pump?Ambalavao,　　 If the power cord is not well contacted, it will also lead to the burning of the motor.　　Potential energy, pumping water up high. However, once the pump can not absorb water, the equipment is shaped like a decoration,ArkarnsSubmersible slurry pump, so what is the reason for this situation? How to solve it?　　 Before starting the submersible slurry pump, the rotor of the rotating pump shall be smooth and even, the outlet sluice valve shall be closed, and water shall be injected into the pump to ensure that the pump is full of water without air.

　　 The submersible slurry pump needs to be inspected after reassembly. If the pulley needs to be rotated by hand, the pump shaft should not be blocked under normal conditions. In addition, the sound of collision between the impeller and the pump shell needs to be avoided.　　The liquid level of slurry shall be higher than the inlet of pump.　　What stands out is the sealing of the container. The seal is easy to install and maintain, stable and reliable, but the price is quite expensive.Where to sell API,　　During adjustment, firstly loosen the support cover, then compress the nut, and then loosen the bearing seat. After adjusting the screw, tighten the compression nut of the bearing seat evenly to make the assembly move towards the pump head. It is necessary to turn the trolley while tightening until the plate does not move. Rotate according to the pump operation　　 If the pump is equipped with a vacuum gauge or pressure gauge, close the cock connected with the submersible slurry pump before starting the motor, open it after the speed is normal, and then gradually open the outlet sluice valve. If the flow is too large, you can properly turn down the gate valve for adjustment. Otherwise, if the flow is too small,Open the gate valve.　　 When adding lubricating oil to the pump at ordinary times, and the excess lubricating oil in the pump must be discharged and replaced regularly.

　　 one method is to use ultrasonic method to detect whether the equipment has cavitation. This method is often convenient for re detection. Even if there is some noise in the surrounding environment, it will not affect the detection results. Therefore, many pumps tend to have better measurement results when in use.Administration,　　This phenomenon shows that the failure of the pump is not only a material problem, but also reminds the pump designers and producers that in addition to good working conditions, the pump should also have good corrosion resistance, high reliability and long service life. The pump shall be designed in addition to the conventional design method of fluid mechanics　　It can be that there is water leakage in the pipe gasket, pipe or pump body. If the current is greater than usual, we should look for problems from the wear of vulnerable parts.　　 The gas inadvertently entered in the equipment is discharged and good sealing performance is ensured.Arkarns,　　 selection of raw materials for flow passage parts: the raw materials for flow passage parts of the pump can be selected according to the particle composition, particle size, hardness,ArkarnsQJ submersible pump, concentration, acid, alkali and other characteristics of the transported materials.　　Generally speaking, the above two cases are the case that the slurry pump does not absorb water. The solutions are also introduced. I believe that people can deal with this problem in time. However, if the problem is serious, you must not adjust it at will. At this time, you should find a professional　　However, there is also a disadvantage of using the auxiliary impeller sealing system, that is, it takes some energy on the auxiliary impeller of the submersible slurry pump, as long as the planning is reasonable this part of the lost flow can be reduced. The slurry pump is mainly applicable to electric power, metallurgy and coal