Cohen Roden kirchenLong shaft submerged slurry pumpWhat kind of benefits does the emergence of bring

　　Some impurities will entangle the impeller,Cohen Roden kirchenSewage pump diving, so generally, the open impeller will be used, so there is no need to worry about getting stuck in the process of transporting sewage.　　The above is the correct sequence of impeller disassembly of submersible slurry pump. Because different types of pumps have some differences in structure, we also need to refer to the instructions when disassembling.Cohen Roden kirchen,　　Ah slurry pump internal structure The pump shaft is bent. After the slurry pump reverses, the reaction force of the impeller may directly top the pump shaft. If the rigidity of the pump shaft is insufficient, resulting in the damage of other accessories in the pump.　　 The rotor assembly is designed according to the actual situation, and the operation is more stable!Beit Jann,　　No matter what type of slurry pump you need, Ritter pump will provide you with the highest quality slurry pump products; The latest development of submersible slurry pump technology in recent years The diving depth has increased from meters to meters!　　Will be scrapped. In addition,Cohen Roden kirchenDrilling fluid slurry pump, since the length of the long shaft is generally fixed, the installation and use of the slurry pump submersible are troublesome and the application occasions are limited. The submersible slurry pump is developed to adapt to increasingly complex working conditions and facilitate the use of users. Its use mode is more　　Compared with the vertical slurry pump, the application market is also larger. In addition to the existing industrial and mining applications of the vertical slurry pump, the submersible slurry pump can also be used as a mobile slurry pump such as sand pumping on board, etc; Submersible slurry pump assembly workshop III. what are the advantages of submersible slurry pump

　　Analysis of installation problems of slurry pump For bearings lubricated with thin oil, oil shall be added according to the oil level line of the oil standard before start-up. Add (HL hydraulic oil in winter and (hl hydraulic oil in summer. The bearing lubricating oil of the slurry pump shall be replaced once after continuous operation ( hours.　　QW (WQ) non clogging submersible sewage pump QW (WQ) non clogging submersible sewage pump IV. the submersible sewage pump uses V power supply, which should be three-phase power supply. If the submersible pump has only two-phase power supply, it will not start. In this case,Cohen Roden kirchenCorrosive pipeline pump, a professional electrician should be asked to use a clamp on ammeter or a submersible pump control　　With the continuous development of slurry pump technology, submersible slurry pump has also responded to the market demand. At the same time, this type of pump is especially suitable for the depth where the vertical slurry pump cannot operate. Pay attention when using the equipment. The submersible slurry pump can operate if its depth is less than m, but it exceedswhere, facilitate users to use, and its use mode is more flexible. And it fills a part of the gap in the application of slurry pump. When the submergence depth is deep and there is no better slurry outlet, that is, in the traditional slurry pump　　 for screws that are too tight or rusted for a long time, the nut can be lubricated with kerosene prepared in advance, or the nut can be gently knocked with a wooden hammer and then removed. This method can also be used in slurry pumps and other places.

　　 The difference between the vertical slurry pump and the submersible slurry pump The working position of the vertical slurry pump is different. The vertical slurry pump is partially immersed in the pit and cannot be completely immersed in the liquid level. The submersible slurry pump can be completely immersed (including the motor part) below the liquid level; Use of motor for vertical slurry pumpInspection standard,　　Turn on the power supply type fool operation; It has a wide range of applications. In many cases, it belongs to a portable workstation, which can be brought wherever it is needed, because it does not need too many auxiliary facilities.　　 whether there is oil　　The above introduction is about the cause ysis of the overload of the slurry pump. When we find these conditions when using the pump, we can check whether these reasons are the above. This is also a reminder that we need to maintain the pump during normal use. latentCohen Roden kirchen,　　The operating environment is different: the key difference between the submersible slurry pump and the vertical slurry pump lies in diving. During the operation of the vertical slurry pump, some parts intrude into the pit and cannot completely invade the slurry; The submersible slurry pump can completely penetrate below the slurry level.　　It is an auxiliary means of on-site monitoring. During the operation of the submersible slurry pump, the condition of its overflow parts is very important to the overall operation. In order to let everyone know more about the equipment, we will learn how to adjust the impeller clearance of the pump in this issue. I hope it will help you.　　 Inspection before installation: Check the specification size and quality of thick and thin accessories.