PforzheimQuotation slurry pumpUnderstand the market

　　 selection of raw materials for flow passage parts: the raw materials for flow passage parts of the pump can be selected according to the particle composition, shape hardness, concentration, acid, alkali and other characteristics of the transported materials.　When using the submersible slurry pump, the equipment may be burned out. The main reason for this phenomenon is improper operation. How should we prevent the burning out?Pforzheim,　　Test the steering first and then connect the motor to the ash pump. There is a removal ring at the journal. This device can prevent the impeller from reversing.　　However, there is also a disadvantage of using the auxiliary impeller sealing system, that is, it takes some energy on the auxiliary impeller of the submersible slurry pump, which is generally about %. However, as long as the planning is reasonable, this part of the lost flow can be reduced. The slurry pump is mainly applicable to electric power, metallurgy and coalPlaneta Rica,　　In fact, the impeller clearance of submersible slurry pump is not adjustable for all types of pump, but it is adjustable. During normal operation, the clearance needs to be adjusted regularly to keep the clearance within the range suitable for normal operation.　　Therefore, the stator winding will be burnt out due to excessive temperature rise.　　 Next, it is necessary to check the water seal. If the water seal is bakelite and the wear is not too serious, you can place abrasive cloth on the glass or dry wood, and then grind the water seal of Boshan submersible slurry pump flat or turn it over for use. However, if the thrust rubber water seal is used, when

　　When the submersible slurry pump works, the pump needs to be placed on land, the suction pipe needs to be placed in water, and the pump needs to be started. Due to special structural requirements, when the slurry pump motor is submerged in the water, the slurry pump and submerged slurry circulating pump need to be placed above the water surface, so they need to be fixed, otherwise the motor will fall into the water　　 Working conditions　　 the water pipe shall be short, and the cavitation allowance of the device shall be greater than that of the pump. It is recommended to use the reverse charging installation method when transporting residues with high weight concentration.average method,　　Many people do not know much about the packing and sealing of equipment because of the equipment of mass and energy. Next, let&#;s learn about the packaging and sealing method of the equipment: packing sealing is very common in submersible slurry pumps. This method has good sealing performance, is easy to use, and effectively reduces the wear of the host and anti vibration kinetic energy　　At present, mechanical seals occupy an increasing share in the slurry pump seal market.　　 If the impeller of the pump is damaged after a long time of use, it will also lead to insufficient liquid supply for the pump.

　　 It is also possible that the fan blades of the pump are few and the air volume is insufficient,PforzheimHH slurry pump,　　Moreover, because the length of the long shaft is generally fixed,PforzheimPipeline pump,PforzheimFire deep well pump, it is often troublesome to install it. Therefore, when it is used later, the place where it operates will also be limited. If the equipment will　　Ensure that the power supply voltage is adjusted to the standard power supply to solve the problem.　　In this way, when the equipment is used again, and the power consumption is also less, and the efficiency of the pump in use is often improved, and the fact isPforzheim　　According to the user&#;s requirements, the motor can add a variety of protection devices such as water inflow detection and overheating, so that the product can operate safely for a long time under adverse working conditions.　　When the water pump is driven by electricity or diesel engine, its impeller (like an electric fan) rotates wildly, thus forming a vacuum in the impeller. In this way, from a al point of view, it is to convert electrical or chemical energy into gravity　　Therefore, when the pump temperature is too high, you don&#;t need to panic. You can quickly troubleshoot according to the above-mentioned reasons, so as to find out the root cause of the excessive temperature of the equipment in time, and then take relative measures to effectively solve it.