Saint Peter Port Sewage pump divingHot discussion on innovation direction of Technology

　　 fold the three layers in half with self-adhesive butyl tape and gradually extend to the outside of the core. When winding, the tape shall be stretched twice, and then the three layers shall be folded in half with PVC tape to ensure that the winding part is not less than mm, and the positions of the three joints shall be staggered for a certain distance in order to prevent short circuit.　　Water or air leakage in the pipeline. The nut may not be tightened during installation. If the leakage is not serious, the air or water leakage can be treated with cement or cement slurry mixed with asphalt oil. Temporary repairs can be done with some wet mud or soft soap. If water leaks at the water pump joint, tighten the nut with a wrench. asSaint Peter Port ,　　 Pipeline booster pump: in fact, the pipeline booster pump is what we often call a booster pump. It is named according to the purpose of the pump. As the name suggests, such as centrifugal pump, pipeline　　Pump. In addition, the submersible slurry pump is mainly characterized by 'slurry', which is wear-resistant and particle passing.San Luis,　　Yes, such mechanical faults will cause the stator winding of the pump to be burnt out.　　In order to ensure the demand for water and electricity for production and living, many units,Saint Peter Port Split vertical pipeline pump, hotels and residential areas in various provinces and cities in China have purchased it and generators. Many enterprises have also purchased generators out of their own pockets in order not to delay production. Driven by this, it and the generator naturally become popular　　When using the submersible slurry pump, we should do a good job in all aspects of commissioning and precautions. We also need to do a good job in protecting the equipment parts and some parts of the motor. Only in this way can we avoid the impact of water and other impurities entering the motor

　　 There is also a vibration method to measure the vibration frequency of the pump, and the measurement is relatively simple. However, when using one method, the measurement results may have some errors. When using the submersible slurry pump, there are other vibration sources that will affect the measurement results, so it is actually the main　　Will the submersible sewage pump get sick?　　 When starting the slurry pump, the outlet gate valve shall be (closed or slightly opened by /. Before starting the slurry pump, expand the pump inlet valve and close the pump outlet valve. Then start the pump. After the pump is started, slowly start the pump outlet valve. The size and speed of opening the pump outlet valve should be based on the fact that the pump does not vibrate and the motorTest method,Saint Peter Port Deep well pump,　　The above four methods can be used to detect whether the submersible slurry pump has cavitation, because if the equipment is in use, it will also have a certain impact on other parts of the equipment. Sometimes submersible slurry pump　　When the submersible slurry pump is used at ordinary times, cavitation usually occurs, otherwise the effect of the submersible slurry pump may not be obvious.

　　 It may be that the motor power of the water pump is too large the working current is too large, and the heat generation is too large resulting in the high temperature of the vacuum pump.Packaging strategy, the water consumption will increase. Therefore　　The use of water pumps is related to all aspects of our life. With the arrival of the May Day holiday, it is necessary for us to choose a suitable water pump.　　Clean up the silt and other obstructions in or around the water pump.　　The pump should be divided into two aspects: electricity and machinery. As for machinery, you can compare the previous maintenance records. The second is electricity. You should know the power of each pump motor and have a certain understanding of its control system. Slurry pump with mechanical sealSaint Peter Port ,　　 Impeller protection in order to ensure the operation of the submersible slurry pump, it is necessary to timely adjust the clearance between the impeller and the front guard plate. When adjusting the impeller clearance, first stop the pump, loosen the bolts pressing the bearing box, loosen the adjusting nuts, make the bearing components move forward,Saint Peter Port Corrosive pipeline pump, and roll the shaft by hand to press the　　 First remove the pump from the engine.　　 If the hot water within ℃ is recommended, the hot water pump must be used, and the external tap water shall be connected for cooling during operation, otherwise the motor will not be burned due to too high medium temperature.