Torneo Installation of medical cold storageIndustry strategic opportunities

Reasonable space: the power consumption of the cold storage is calculated according to the cold consumption of the cold storage which usually includes two parts: the cold consumption during cargo cooling and refrigeration; It is the cooling consumption of the refrigeration room itself and operation management.Judge the operating sound of the compressor, and carefully listen to the operating sound of water pump, cooling tower, compressor, fan and other equipment. In case of abnormal sound, timely warranty is required, so as to avoid greater damage to the compressor due to untimely warranty.Torneo ,Because our large-scale fresh-keeping warehouse is generally composed of many thermal insulation boards, and the gap between each board is the place that needs maintenance. During construction, these gaps will generally be sealed with sealant,Torneo Cold storage, but if it is found that there are seal failure departments in the fresh-keeping warehouse during use, they need to be repaired in time.Fault phenomenon: fan motor overload, compressor line is disconnected, fuse is blown, thermal relay acts, high voltage switch acts, line is falsely connected or loose fault phenomenon: it stops in a short time after drying, ambient temperature is too high, condenser is blockedJena,Technical assurance measures for the installation of cold storage: during production in the production workshop, the production shall be carried out in strict accordance with the operation rules specified in ISO quality operation, self inspection and inspection application shall be carried out to ensure that the factory pass rate is, and unqualified products are not allowed to leave the factory.The refrigeration equipment in the fresh-keeping environment of the quick-frozen warehouse mostly adopts the single-stage compression refrigeration system, with freon as the refrigerant. The evaporation mode in the warehouse is the cooling fan, which can be ceiling type. If the number of warehouses is small and the volume does not exceed cubic meters, the refrigeration mode of the warehouse machine can be considered. If there are a large number of warehouses, the mode of multiple heads in parallel can be considered.The evaporator surface is too thick or too much dust, and the heat transfer effect decreases: another important reason is that the heat transfer efficiency of evaporator is low, which is mainly caused by excessive frost or excessive dust on the evaporator surface.

Moreover polyurethane does not produce harmful gas at high temperature.How to judge whether the controlled atmosphere storage is bad and the effect is poor? Under the same conditions, the required temperature can be reached in minutes, but now it takes minutes. In this way, the refrigeration is obviously slow and the effect is poor, which will directly affect the use cost.The refrigerant charge is insufficient. At this time, just add enough refrigerant.High quality and low price,Torneo Which is a good place to install fruit and vegetable cold storage, that is, and problems of user air switch; Input voltage is too low; The star angle conversion interval is too short (it should be ~ seconds); Hydraulic cylinder failure (no reset); Intake valve failure (too large opening or stuck); Loose wiring; Host failure; Main motor fault; TR time relay is broken (relay unit).The cold storage belongs to a kind of refrigeration equipment. Compared with the refrigerator, its refrigeration area is large, but they have the same refrigeration principle. So how to maintain the cold storage every day. Today I'll introduce how to do a good job in the daily management and maintenance after the installation of the cold storage.

Artificial refrigeration keeps the room at a constant temperature. The walls, floors and flat roofs of large cold storages are laid with thermal insulation materials with a certain thickness to reduce the incoming heat from the outside. In order to reduce the absorption of solar radiation, the surface of the external wall of the cold storage is painted white or light color.Job description,When the cold storage is built, the diffusion of water vapor and the infiltration of air shall be prevented. When outdoor air invades, it will not only increase the cold consumption of the cold storage, but also bring moisture into the warehouse. Moisture condensation will damp the heat insulation structure and freeze and damage the cold storage structure. Therefore, it is necessary to set moisture-proof and heat insulation layer, professional cold storage installation, installation of cold storage, fruit fresh-keeping cold storage, medical cold storage and other products which have a complete variety, sell well at home and abroad, and have a long service life! Products lead the wire industry. Welcome to inquire, so that the cold storage building has good sealing, moisture-proof and steam isolation performance.The water-cooled cold storage shall keep the cooling water tower clean and keep the air around the water tower circulating with low temperature, so as to avoid sundries from entering the cooling tower and reduce the heat dissipation efficiency.Here we focus on polyurethane. Polyurethane is an ideal cold storage material in the cold storage project. Superior bonding properties make the foam and metal panels form a solid whole, so that no other adhesive materials are needed. When polyurethane is used as a cold storage project, rigid polyurethane foam is formed between the panels of the storehouse panel, and then solidified and pressed to form a multi shape storeboard, because the metal plate can roll out different waveforms, so that the overall rigidity is stronger and the bearing capacity is higher. Polyurethane filler board can meet the firmness and physical requirements of exterior wall and can be used in various cold storage projects. It is technically feasible and cost-effective. Yuanbao refrigeration believes that polyurethane is one of the new cold storage materials with great development prospects in the future. The thermal insulation materials of cold storage engineering should not only have good thermal insulation performance, but also be economical, applicable and environmental friendly. To ensure the smooth progress of our cold storage project, we should not only inquire about the raw materials of the cold storage, but also the types of cold storage. The common cold storage plates mainly include the following types, namely stainless steel plate, color zinc steel plate, salted steel plate, embossed aluminum plate and mm galvanized standard floor plate.Torneo ,Energy saving and power saving: the design cost of quick freezing warehouse mentioned above is very low, but it has a great impact on the cost of quick freezing warehouse and later use cost. The electricity bill is often an important expenditure item in the later stage. The design scheme of the show can greatly reduce the power consumption of the quick freezing warehouse. The selection of the back sunny side of the quick freezing warehouse, the selection of the thickness of the thermal insulation board should be appropriate, the tightness of the quick freezing warehouse door, and the temperature difference between the adjacent cold storage rooms should not be too large are all issues that we need to consider. There are also some tips such as the use of air curtain machine on the quick freezing warehouse door. We remind users to use parallel units in quick freezing warehouse as far as possible and start them reasonably.These are several very common cold storage materials. The use of these materials has greatly improved the thermal insulation and refrigeration performance of the cold storage, which makes people's retained items more convenient and reliable. With the continuous development of material technology today's various cold storage materials emerge in endlessly, and the cold storage is different from each other. When purchasing, we should make reasonable comparison and select products suitable for our own use needs and economic conditions.Anti odor floor drain shall be set on the pavement of refrigeration room and refrigeration unit room, and the height width ratio of floor drain water seal shall not be less than mm. The elevator shaft, electronic pit and other places convenient for drainage shall be provided with drainage and equipment to avoid backflow of water.