San JoseAluminum alloy mast type elevatorNew trade model of governance

Working on an aluminum alloy elevator workbench. Must wear safety belts, helmets, and other tools to prevent accidents.Method for hydraulic oil leakage in aluminum alloy elevator: Check if the pipe joints are loose and try to tighten them. Check if the viscosity of the hydraulic oil used is too low. When checking the leakage point of the hydraulic oil system, generally,San JoseAluminum alloy high-altitude work elevator, the place where hydraulic oil seeps out is the leakage point, but it is not ruled out that the leaked hydraulic oil may accumulate along the pipeline deviating from the leakage point. Therefore, it is important to carefully search during inspection. High priced aluminum alloy elevator manufacturers of various specifications welcome scrap merchants, industrial companies, enterprises, and power departments to visit and negotiate with the company!San Jose,A self-developed integrated built-in slider is used between each mast to minimize the dynamic gap between the masts.The main components of the Hunter hydraulic fixed elevator are: . The shaft part is a closed or mesh frame enclosed by buildings or lightweight steel structures, with steel guide rails installed on both sides of the interior. . The driving part is equipped with a hydraulic drive motor, oil pump, and safety valve, with manual and automatic doors. Generally, open platforms do not have doors. . The electrical part: It includes power, signal, Composition of safety and lighting devices: Platform parts: It is a steel structure platform that carries heavy objects, which can be closed (i.e. cabin type) or open, with guide rollers or guide shoes installed on both sides. The bottom of the platform can be connected to a lifting oil cylinder or a lifting shear fork shaped steel frame. When we use aluminum alloy elevators, we need to regularly inspect, maintain, and maintain them, which can not only extend the service life of the aluminum alloy elevator, Can make it work with greater power! For example, the transmission part should have sufficient oil, repaired, or replaced. Mechanical bolts, especially parts that frequently vibrate, such as slewing bearings and lifting arm connecting bolts, should be checked for looseness. If there is looseness, it must be tightened or replaced immediately. Next, let's take a look at the regulations for the maintenance time of aluminum alloy elevators: daily maintenance (carried out per shift).Uppsala,The protected leg structure makes work safer and can be used for lifting and lowering operations close to the working face.Hydraulic lifting platform products are divided into curved arm hydraulic aluminum alloy elevators, scissor fork hydraulic aluminum alloy elevators, mast hydraulic aluminum alloy elevators, and straight arm hydraulic aluminum alloy elevators according to their working modes. Hydraulic aluminum alloy elevator is a replacement product of folding arm aluminum alloy elevator (lifting platform) and scissor fork aluminum alloy elevator (lifting platform). It can be widely used for the decoration and decoration of stations, docks, airports, hotels, posts and telecommunications, municipal gardens, grain depots, cleaning companies, public building facades, or the installation and maintenance of power systems. This aluminum alloy elevator has the advantages of light weight, self-propelled walking, electric starting, self supporting legs, simple operation, and especially the ability to cross obstacles for high-altitude operations.Summary: Elevators can be large or small, and regardless of size, fixed, telescopic table top, wall mounted elevator, folding elevator, car mounted (diesel), self-propelled and other aluminum alloy elevators.Introduction to aluminum alloy elevator: Aluminum alloy elevator is a fixed transportation equipment that lifts items from one height to another. Due to the large weight and volume of the lifted object, it is safe and stable. It can be used as a specialized hydraulic lifting platform product for transporting goods between floors of buildings with the main function of transporting various work floor goods up and down; At present, aluminum alloy elevators are mostly used in the market for lifting cars in three-dimensional garages and garage floors.Inspection standardGood driving performance reduces noise, increases the clearance inside the platform, and also makes the transmission smoother and the mechanism vibrates less.In low concentration carbon monoxide gas. It can cause symptoms such as headache, shortness of breath, nausea and vomiting, body weakness and dizziness, psychological confusion, it can cause death, such as starting the engine of the equipment in the garage.It is strictly prohibited to run the engine for a long time in a closed garage. The exhaust gas of the aluminum alloy elevator engine contains carbon monoxide. This is a toxic gas that has been in low concentration for a long time

Users can choose the power mode and configuration according to their usage range: the power system includes: DC power supply, single-phase or three-phase power supply, diesel engine. Walking: assisted self-propelled, two wheel traction, self driving, and car modification. Outriggers: mechanical outriggers, hydraulic outriggers ordinary hand cranked outriggers, and pull-out outriggers. System: explosion-proof electronic control system,San JoseMast type aluminum alloy lifting platform, remote control system, PIC system. Hydraulic pump station: domestic lifting platform dedicated pump station imported pump station from Italy with external protective devices: organ cover type, mesh type, and iron plate sealed type.index,The contact opening and closing of the travel switch of each safety device must be reliable, and the contact crater should be polished in a timely manner.Classification of aluminum alloy lifting platforms: single column aluminum alloy elevators; Double column aluminum alloy elevator; Three pillar aluminum alloy elevator; Four pillar aluminum alloy elevator; Placed aluminum alloy elevator.Users can choose the power mode and configuration according to their usage range: the power system includes: DC power supply, single-phase or three-phase power supply, diesel engine. Walking: assisted self-propelled, two wheel traction, self driving, and car modification. Outriggers: mechanical outriggers, hydraulic outriggers, ordinary hand cranked outriggers, and pull-out outriggers. System: explosion-proof electronic control system, remote control system, PIC system. Hydraulic pump station: domestic lifting platform dedicated pump station, imported pump station from Italy with external protective devices: organ cover type mesh type, and iron plate sealed type.San Jose,The lifting product has a sturdy structure, large load-bearing capacity, stable lifting, simple and convenient installation and maintenance, making it an ideal economic and practical cargo conveying equipment for replacing elevators between low floors. If the required size is large, a fixed double span hydraulic lift can be used. The double span lift is stable, has a large bearing capacity, and is easy to operate. It is widely used in industries such as vehicle maintenance, kilns, and equipment matching.The lifting product has a sturdy structure, large load-bearing capacity, stable lifting simple and convenient installation and maintenance, making it an ideal economic and practical cargo conveying equipment for replacing elevators between low floors. If the required size is large, a fixed double span hydraulic lift can be used. The double span lift is stable, has a large bearing capacity, and is easy to operate. It is widely used in industries such as vehicle maintenance, kilns, and equipment matching.The lifting product has a sturdy structure, large load-bearing capacity, simple and convenient installation and maintenance,San JoseAluminum alloy double column elevator, making it an ideal economic and practical cargo conveying equipment for replacing elevators between low floors. If the required size is large, a fixed double span hydraulic lift can be used. The double span lift is stable has a large bearing capacity, and is easy to operate. It is widely used in industries such as vehicle maintenance, kilns, and equipment matching.