ElhovoScrew deep well pumpCategory application analysis of

　　Adjustment. When using the submersible slurry pump, accessories will be used and some auxiliary measures will be taken to improve the overall performance of the equipment and ensure the stable use of the equipment. Many users do not pay attention to these things when using them,ElhovoCarbon steel explosion-proof pipeline pump, which will cause equipment problems and affect work efficiency. So we&#;re using　　When this type of pump is used at ordinary times, the pump and motor operate in a coaxial whole. When it runs, the motor shaft will drive the impeller of the pump to rotate, and then at this time the rotating force can be brought to the medium, so thatElhovo,　　Shaft seal water, no dilution of pulp, good shaft seal effect. It can be used when the slurry is not allowed to be diluted.　　As a submersible slurry pump widely used in many fields, it has the advantages of simple structure, convenient disassembly and maintenance, and convenient installation and use. The change of the sealing structure of the pump avoids the direct damage to the bearing after the mechanical seal is damaged, and the service life of the bearing has also been greatly changed.Hawsh Isa,　　The above is a brief introduction to the effect and form of shaft seal of submersible slurry pump. Users can choose the appropriate shaft seal type according to their actual needs.　　 During the installation of smooth bearing components, if the installation is correct, the smooth oil is appropriate, the repair is timely, the repair personnel should regularly repair the bearing components, check the condition of the bearings and the smooth oil, and regularly add or replace the smooth oil during the work, and the management is easier. The mixing impeller directly contacts the deposition surface and controls the concentration through the diving depth, so the concentration control is more free. Equipment directly submerged　　 The reasons for excessive power loss are as follows: the running speed of the screw rod is too high.　　Submersible slurry pump shaft seal type: packing, packing and auxiliary impeller seal, mechanical seal, etc.Project scope,　　In fact the impeller clearance of submersible slurry pump is not adjustable for all types of pump, but it is adjustable. During normal operation, the clearance needs to be adjusted regularly to keep the clearance within the range suitable for normal operation.　　Troubleshooting: first increase the water pressure, then inject water into the pump body, and then start the pump. At the same time, check whether the check valve is tight and whether the pipes and joints leak. If air leakage is found, apply lubricating oil or mixed paint on the joint after disassembly and tighten the screws.　　Will be scrapped. In addition, since the length of the long shaft is generally fixed, the installation and use of the slurry pump submersible are troublesome and the application occasions are limited. It is normal to use the equipment for a long time, for example, when the submersible slurry pump is used at ordinary times, air holes usually appear

　　The non service life of the equipment is not as long as possible. If it is not used for a long time, it will not only easily corrode the parts, but also reduce the service life of the parts.ranking,　　Yes, such mechanical faults will cause the stator winding of the pump to be burnt out.　　 The pump fails to supply water or the flow is insufficient. The pump fails to supply water or the flow is insufficient. It is likely that the suction pipe has water leakage or the bottom valve has air leakage, but there are several possible reasons: the water inlet is blocked; The bottom valve is not deep enough underwater; The running speed of the water pump is not enough; leaf　　It will burn out. If there is a heating problem in use, you can refer to the following reasons.Elhovo,　　 the submersible slag pump is often used to transport pulp containing solid particles, so the wear resistance of the pipeline should also be considered.　　Submersible slurry pump it fills the gap in the application of slurry pump. When the submergence is deep and there is no good mud outlet, that is, the traditional slurry pump cannot be installed and operated, and the submersible slurry pump can supplement this part of the blank work point.　　Potential energy, pumping water up high. However,ElhovoUsed pipeline pump,ElhovoSubmersible pump can pump sewage, once the pump can not absorb water, the equipment is shaped like a decoration, so what is the reason for this situation? How to solve it?