EspazaGalvanized greenhouse square pipeMaintenance of main components

The principle is similar to that of the plate rolling machine. The bending machine can determine a circle. Adjust the height to adjust the curvature.Hardness hardness is a pointer to measure the hardness and softness of metal materials. At present, the hardness method is commonly used to measure the hardness in production. It uses the indenter with fixed geometry to measure the hardness value of the metal material surface tested under fixed load according to the degree of hardness.Espaza,Low alloy steel is divided into q Mn, Q, St-, etc.Strength refers to the performance of metal materials under static load (excessive plastic deformation or fracture). Since the action modes of load include tension, compression, bending and shear, the strength is also divided into tensile strength, compressive strength, flexural strength and shear strength. There is often a certain between various strengths. Generally, tensile strength is used as the basic strength indicator. Appropriate sites and warehouses shall be selected. The sites or warehouses for storing steel pipes shall be in clean and unobstructed places, away from factories and mines that produce harmful gas or dust. Weeds and sundries shall be removed on the site to keep the steel pipe clean; In the warehouse, it is not allowed to stack with acid alkali, salt, cement and other materials that are corrosive to the steel pipe. Different types of steel pipes shall be stacked separately to prevent confusion and corrosion; Large section steel, rail, steel plate, large-diameter steel pipe, forging, etc. can be stacked in the open air; Small and medium-sized section steel, reinforcement, medium diameter steel pipe, steel wire and steel wire rope can be stored in a well ventilated shed, but they must be covered and padded; Some small steel pipes, steel sheets, steel strips, silicon steel sheets, or thin-walled steel pipes, all kinds of cold-rolled and cold drawn steel pipes and high and corrosive metal products can be stored in the warehouse; The warehouse shall be selected according to geographical conditions, and generally adopts ordinary closed warehouse, that is, the warehouse with roof, enclosure, tight doors and windows and ventilation devices; The warehouse is required to pay attention to ventilation in sunny days, close and damp proof in rainy days, and often maintain a suitable storage environment. The principle of reasonable stacking and first in first stacking is to stack according to varieties and specifications under the condition of stable stacking and ensuring safety. Materials of different varieties shall be stacked separately to prevent confusion and mutual corrosion; It is forbidden to store articles that have corrosive effect on steel pipes near the stacking position; The bottom of the stack shall be padded high, firm and flat to prevent the material from moisture or deformation; The same kind of materials shall be stacked according to the warehousing order, so as to facilitate the implementation of the principle of first in, first out; The section steel stacked in the open air must be provided with wooden mats or strip stones. The stacking surface is slightly inclined to facilitate drainage. Pay attention to the straightness of the material placement to prevent bending and deformation; The stacking height shall not exceed m for manual operation, m for mechanical operation, and m for stacking width; A fixed channel shall be reserved between stacks, generally .m, and the access channel is generally ~ om depending on the size of materials and transportation machinery; The bottom of the stack shall be padded up. If the warehouse is cement floor, it can be padded up by .M; If it is muddy ground, it must be padded . ~ .m high. If it is an open site, the cement ground shall be padded with O & middot; ～O· m, . ~ . m higher than the sand and mud surface, the angle steel and channel steel shall be stacked in the open air, i.e. the mouth shall face down, and the I-beam shall be placed vertically. The i-groove surface of the steel pipe shall not face up to avoid ponding and rust. The packaging and protective layer of the protective materials shall be coated with agent or other plating and packaging before leaving the factory, which is an important measure to prevent material corrosion. Attention shall be paid to protection during transportation, loading and unloading and shall not be damaged, The storage period of materials can be extended, the warehouse shall be kept clean and the maintenance of materials shall be strengthened. Before warehousing, such as steel wire brush for high hardness and cloth, cotton and other materials for low hardness; The materials shall be regularly after warehousing. If there is corrosion, the corrosion layer shall be removed; Generally, the steel pipe surface does not need to be coated with oil after being cleaned, but for high-quality steel, alloy steel sheet, thin-walled pipe, alloy steel pipe, etc., the internal and external surfaces need to be coated with anti rust oil before storage; Steel pipes with serious corrosion shall not be kept for a long time after rust removal and shall be used as soon as possible. With the development of economy, rectangular tubes, seamless square tubes, galvanized square tubes and galvanized tubes have been recognized by the majority of customers for a long time. There are more and more counterfeit products on the market. In order to prevent being deceived when you are in square tubes, you need to know some knowledge about how to judge the authenticity of square tubes: & ldquo; We can judge by observing the surface and flatness of the square tube. If the surface of the square tube is relatively flat, it can reflect that the square tube is good. On the contrary, if the surface is not goodKaarinaSquare pipe is the name of square pipe, that is, steel pipe with equal side length. It is made of rolled strip steel after process treatment.A. square tube structural steel: (a) high quality carbon structural steel; (b) Alloy structural steel; (c) Spring steel; (d) Easy cutting steel; (e) Bearing steel; (f) High quality structural steel for specific purposes.After cold drawing and aging treatment, the yield point is improved, the tensile ultimate strength is also increased, and the plasticity continues to decrease. Due to the reduction of internal stress during aging, the modulus can be basically restored. According to this principle, cold drawing or cold drawing of reinforcement or low carbon steel wire rod is often carried out on site or prefabricated component factory, so as to improve yield strength and save steel.

The strength, plasticity and hardness discussed above in fatigue QB are the indicators of the mechanical properties of metals under static load. In fact, many machine parts work under cyclic load, under which fatigue will occur.Compared with other traditional pipes, square pipe supply steel pipe has lighter raw materials, high strength, good resistance, can withstand high internal pressure, sensitive application, and can get used to messy or bad geological conditions.Empty bending empty bending is the bending moment formed in one direction between the outer roll and the outer wall of the tube blank to bend the strip. Empty bending will compress the bending line, and the metal at the bending will accumulate and thicken, which is the compression thickening effect of empty bending.Promise and keep promise,C. electric furnace steel: (a) electric arc furnace steel; (b) Electroslag furnace steel; (c) Induction furnace steel; (d) Vacuum consumable furnace steel; (e) Electron beam furnace steel.Square pipe is the name of square pipe, that is, steel pipe with equal side length. It is made of rolled strip steel after process treatment.The principle is similar to that of the plate rolling machine. The bending machine can determine a circle. Adjust the height to adjust the curvature.

Comprehensive classification ordinary steel A. carbon structural steel: (a) Q (b) Q (b); (c) Q( C)； (d) Q( B)； (e) Q.Process inspection,It should be noted that the position of the disc from the calibration line can be adjusted according to the reinforcement diameter, and R and R can be equal or different.Square pipe, the steel pipe whose ratio of outer diameter to wall thickness is less than is called square pipe. At present, the square tubes produced by qb square tube factory are mainly used in tap water engineering, electric power industry, agricultural irrigation and urban construction. For transportation: water supply and drainage. For gas transmission: gas, steam and liquefied petroleum gas. For structure: for punchingSteel used & mdash& mdash; Such as bridge steel, ship steel, boiler steel, pressure vessel steel, agricultural machinery steel, etc.EspazaIn recent years, large-diameter seamless square tube plays a good role in economic development. Because there are many types of large-diameter seamless square tubes, the continuous casting process of large-diameter seamless square tubes is also different. What are the specific steps of the continuous casting process of large-diameter seamless square tube? As the name suggests, square tube is a kind of square tube type. Many materials can form square tube body. Its medium is used for what purpose and where it is used. Most square tubes are steel tubes which are unpacked, leveled, crimped and welded to form round tubes, Then the round pipe is rolled into a square pipe, and then cut into the required length. Generally, square tubes per package are mostly in large specifications in terms of spot, and . - ~~ - square tubes are divided into structural square tubes, decorative square tubes, building square tubes, mechanical square tubes, etc. according to their uses.Strength refers to the performance of metal materials under static load (excessive plastic deformation or fracture). Since the action modes of load include tension, compression, bending and shear, the strength is also divided into tensile strength,EspazaGalvanized Q235 square pipe, compressive strength, flexural strength and shear strength. There is often a certain between various strengths. Generally tensile strength is used as the basic strength indicator. Appropriate sites and warehouses shall be selected. The sites or warehouses for storing steel pipes shall be in clean and unobstructed places, away from factories and mines that produce harmful gas or dust. Weeds and sundries shall be removed on the site to keep the steel pipe clean; In the warehouse, it is not allowed to stack with acid, alkali, salt cement and other materials that are corrosive to the steel pipe. Different types of steel pipes shall be stacked separately to prevent confusion and corrosion; Large section steel, large-diameter steel pipe steel plate, forging etc. can be stacked in the open air; Small and medium-sized section steel, wire rod, reinforcement, medium diameter steel pipe, steel wire and steel wire rope can be stored in a well ventilated shed, but they must be covered and padded; Some small steel pipes, steel sheets, steel strips, silicon steel sheets, or thin-walled steel pipes, all kinds of cold-rolled and cold drawn steel pipes and high and corrosive metal products can be stored in the warehouse; The warehouse shall be selected according to geographical conditions, and generally adopts ordinary closed warehouse, that is, the warehouse with roof, enclosure, tight doors and windows and ventilation devices; The warehouse is required to pay attention to ventilation in sunny days, close and damp proof in rainy days, and often maintain a suitable storage environment. The principle of reasonable stacking and first in first stacking is to stack according to varieties and specifications under the condition of stable stacking and ensuring safety. Materials of different varieties shall be stacked separately to prevent confusion and mutual corrosion; It is forbidden to store articles that have corrosive effect on steel pipes near the stacking position; The bottom of the stack shall be padded high, firm and flat to prevent the material from moisture or deformation; The same kind of materials shall be stacked according to the warehousing order, so as to facilitate the implementation of the principle of first in, first out; The section steel stacked in the open air must be provided with wooden mats or strip stones. The stacking surface is slightly inclined to facilitate drainage. Pay attention to the straightness of the material placement to prevent bending and deformation; The stacking height shall not exceed m for manual operation, m for mechanical operation, and m for stacking width; A fixed channel shall be reserved between stacks, and the access channel is generally ~ om depending on the size of materials and transportation machinery; The bottom of the stack shall be padded up. If the warehouse is cement floor, it can be padded up by .M; If it is muddy ground, it must be padded . ~ .m high. If it is an open site, the cement ground shall be padded with O & middot; ～O· m, . ~ . m higher than the sand and mud surface, the angle steel and channel steel shall be stacked in the open air, i.e. the mouth shall face down, and the I-beam shall be placed vertically. The i-groove surface of the steel pipe shall not face up to avoid ponding and rust. The packaging and protective layer of the protective materials shall be coated with agent or other plating and packaging before leaving the factory, which is an important measure to prevent material corrosion. Attention shall be paid to protection during transportation, loading and unloading and shall not be damaged, The storage period of materials can be extended, the warehouse shall be kept clean and the maintenance of materials shall be strengthened. Before warehousing, materials shall be prevented from being drenched or mixed with impurities. Materials that have been drenched or contaminated shall be wiped according to their properties, such as steel wire brush for high hardness and cloth, cotton and other materials for low hardness; The materials shall be regularly after warehousing. If there is corrosion, the corrosion layer shall be removed; Generally, the steel pipe surface does not need to be coated with oil after being cleaned, but for high-quality steel alloy steel sheet, thin-walled pipe, alloy steel pipe etc., the internal and external surfaces need to be coated with anti rust oil before storage; Steel pipes with serious corrosion shall not be kept for a long time after rust removal and shall be used as soon as possible. With the development of economy,EspazaHow much is the price of galvanized steel pipe per meter, all kinds of square tubes, rectangular tubes, seamless square tubes, galvanized square tubes and galvanized tubes have been recognized by the majority of customers for a long time. There are more and more counterfeit products on the market. In order to prevent being deceived when you are in square tubes, it can reflect that the square tube is good. On the contrary, if the surface is not goodFor structure: as pile driving pipe and bridge; pipe for wharf, marine pile driving pipe, etc.