Hamburg NorthHydraulic lifting platformBeloved by many manufacturers

Remember not to overload, overload is the root cause of many faults.The manufacturer of hydraulic cargo elevators reminds the use of guide rail hydraulic lifting cargo elevators. Guide rail hydraulic lifting cargo elevators: Do not stand within the specified range, prohibit any idle personnel from entering the work area, ensure that the work area is free of clothing, and maintain a clean and tidy workplace.Hamburg North,Cylinder diameter and hydraulic oil flow rate. The speed of the hydraulic lifting device is inversely proportional to the cross-sectional area of the cylinder rod and directly proportional to the flow rate of hydraulic oil. When the hydraulic elevator runs slowly, priority should be given to the hydraulic oil flow angle.When using hydraulic elevators the main causes of noise are mechanical mechanism failures, hydraulic system failures, electrical equipment or component failures, etc. Today, the manufacturer of hydraulic cargo elevators will introduce to you the reasons for the noise generated by hydraulic elevators.Pyongyang,There are many reasons for unstable workbench descent, such as overload, severe eccentric load, hydraulic oil impurities, etc. In response to the above reasons, it can be solved by reducing the load, adjusting the center of gravity of the load, and replacing hydraulic oil wholesale for hydraulic cargo elevators.After long-term use of the automatic lifting platform equipment, it is inevitable that some malfunctions will occur. In order not to affect work, it is necessary to promptly solve the difficulties in starting the motor and abnormal sounds. Generally, due to overload, insufficient power supply, and a small cross-sectional area of the power supply cable, the starting voltage drop is too large and the price of the cargo elevator is reduced.The combined platform is often used in small workshops with small volume of goods. However, because this platform needs to complete two functions at the same time, it inevitably increases the distance of handling tools/vehicles in the workshop.

Do not use hydraulic lifting equipment with malfunctioning issues. The problem should be resolved before carrying cargo.Hydraulic cargo elevator: Only when the load of the hydraulic guide rail type lifting cargo elevator cannot start working, should the pressure of the hydraulic system be checked. If the pressure is below the normal range, the set value of the relief valve should be adjusted. Professional elevator manufacturers have high pressure resistance, good waterproof performance, fire and high temperature resistance, strong overload capacity, corrosion resistance, radiation resistance, and long service lifeThere is noise inside the hydraulic cylinder. When replacing the hydraulic oil, there was air in the hydraulic cylinder due to an operational error. Under high pressure, it is easy to generate cavitation and high-frequency noise. When the rod is bent or replaced with a new seal, the new seal is too tight, which can also produce significant noise. If it is a problem of tight sealing, the noise can be reduced after running in for a period of time. If the rod is bent, it needs to be corrected. In addition, hydraulic pipelines should use hoses as much as possible, even when arranging pipelines, it can reduce vibration and noise, and the pipelines should avoid dead bends as much as possible.manufacturer, pay attention to alignment the installation personnel should confirm the infrastructure such as the foundation and shaft, leveling and alignment points, and confirm that the foundation meets the requirements before construction.Set up warning lights around the guide rail type hydraulic cargo elevator equipment, and the warning lights will light up to warn operators when loading and unloading materials. Idle personnel are prohibited from entering the operating range.Each box, distribution box, etc. should be kept clean and promptly cleaned of dust on electrical equipment.

The elevator is evenly distributed at any position on the guide rail at % of the maximum load capacity, and should be stable at the maximum lifting height.Quality management,Regularly check whether each organization is functioning properly and whether there is noise. If problems are found, they should be promptly cleaned up.When repairing the hydraulic system, only clean plastic plugs can be used to seal the end of the pipeline.Materials enter the production line at one end of the factory building, and the production process ends at the other end of the factory building with multiple separate platforms; This can greatly shorten the distance of material flow in the factory building.Hamburg North,When the hydraulic oil of the equipment is insufficient, it will not cause lifting. At this point you only need to add enough hydraulic oil to run.Surface paint quality: The paint should be smooth and flat, have good adhesion with metal, have uniform color, no bubbles, no cracks, and there should be no wrinkles, pits, and sagging.Hydraulic lifting table: the hydraulic lifting table is widely used in various industrial enterprises and production lines such as automobile,Hamburg NorthHydraulic lifting table, container, mold manufacturing, wood processing, chemical filling, etc., to meet the lifting needs of different operation heights, and can be equipped with various table forms (such as ball,Hamburg NorthImported hydraulic lifting platform, roller rotary table, tipping, telescoping), and with various ways (separate,Hamburg NorthType hydraulic lifting platform, linkage, explosion-proof), it has stable and accurate lifting, frequent starting The characteristics of large load capacity effectively solve various lifting and lowering difficulties in industrial enterprises, making production operations smooth.