AnkrajProfessional hydraulic lifting platformVarious application requirements

The main device does not engage. When this fault occurs, check whether the three-phase power supply is normal, whether the internal and external emergency stop button switches, the electric lock switch are turned on, whether the three-phase electrical phase sequence is correct, and whether the relay working indicator light is on.The noise and oil level of the elevator oil cylinder are too low. From the air at the connection of the oil filter or joint to the oil, the coupling inside the oil cylinder is loose. The internal fault of the oil cylinder is that the installation of the oil cylinder motor is not concentric. From the motor, the air and oil at the moving shaft are blocked. The oil return pipe of the oil filter is loose, and the air or oil pipe is on the oil surface, Mixing air into the oil to eliminate: The concentricity should be adjusted to within .MM. The coupling should be repaired or the oil pump should be replaced to increase the oil volume above mm in the oil filter and joint positions. The rotating shaft sealing ring should be replaced to clean the oil filter screen, filter the oil, lock the return oil pipeline, and extend the return oil pipeline below the oil level. If there is air mixed in the oil or the air in the hydraulic cylinder is not completely discharged, it will cause cavitation under high pressure and cause significant noise. At this point, it is necessary to exhaust the air in a timely manner.Ankraj,What technical issues are required for the installation of hydraulic freight elevators? The installation of hydraulic freight elevators is actually quite complex. If you do not understand the equipment pictures designed by the elevator manufacturer and the detailed situation of the hydraulic freight elevator designed by the elevator manufacturer, installation errors may occur, leading to equipment failure of the freight elevator! When installing hydraulic freight elevators, it is necessary to accurately calculate the size of the pit. The guide rail hydraulic freight elevator is a freight elevator composed of chains, guide rail torque tubes, and other components, mainly driven by the chain to assist in the upward and downward telescopic lifting of the freight elevator. The pulleys at the four corners of the countertop should be fixed on the surrounding guide rails. The entire elevator equipment is installed on the wall and wall mounted installation is chosen to enhance the stability of the freight elevator. Choosing the appropriate wall size also requires careful planning.Lines of various safety equipmentAsamankese,Reason: The lowering valve is not tightly closed. Cleaning method: Check if the lowering valve is powered on. If there is no power supply, clear the malfunction of the lowering valve itself or replace the lowering valve. It is necessary to keep the valve of the lowering valve clean and flexible.The vibration range is proportional to the lifting height. The higher the height, the larger the shaking range, especially for mobile hydraulic cargo elevators. When the working height exceeds meters, the wind ropes at the four corners of the hydraulic cargo elevator should be tightened to strengthen leg protection, increase stability, and reduce shaking.Stability: The workbench should evenly withstand % of the MAX load capacity and be stable at the MAX elevation.

Regularly check whether each organization is functioning properly and whether there is noise. If problems are found, they should be promptly cleaned up.When repairing the hydraulic system, only clean plastic plugs can be used to seal the end of the pipeline.The hydraulic lifting platform is a manually movable type, and the lifting power of the platform is a two machine or three-phase power supply. It has manual and electric power, and is also equipped with a hand pump for use in case of power outage. This series of platforms have the characteristics of flexible movement, stable lifting, and easy operation, and are mainly used in factories, government agencies, commercial stores and the construction and decoration industry.device management,When the hydraulic system malfunctions, the hydraulic elevator may experience problems with the hydraulic pump, motor valve,AnkrajProfessional hydraulic lifting platform, and hydraulic installation after repairing the hydraulic system, which can easily cause vibration and generate significant noise.The hydraulic pump produces noise. When the hydraulic elevator rises, the hydraulic pump runs at high speed. If there is a problem with the gears or bearings of the hydraulic pump, which causes periodic changes in the hydraulic system pressure, it will also cause resonance in the hydraulic system and generate noise.Solution: Check if the performance of the legs is good, even if the butter is polished to increase its properties.

The precautions to consider when selecting a hydraulic lift oil tank include: considering the structure of the oil tank, the partition in the traditional oil tank cannot settle dirt. A vertical partition should be installed along the longitudinal axis of the oil tank, with a space left between one end of the partition and the end plate of the oil tank to connect the gaps on both sides of the partition. The inlet and outlet of the hydraulic pump are arranged on both sides of the partition at the disconnected end, so that the distance Z between the inlet and return oil is far, The hydraulic oil tank has more heat dissipation effect.Equipment maintenance,Considering the oil level in the oil tank when all hydraulic cylinders in the system are extended, the oil level in the oil tank should not be lower than the Z-low oil level, and when the oil cylinders retract, the oil level should not be higher than the Z-high oil level. In fact, most manufacturers have noticed the above issues. The reason for the introduction is that most users can learn more about the equipment itself when using elevators,AnkrajMobile hydraulic lifting platform, in order to facilitate equipment maintenance. Hydraulic cargo elevator manufacturers sincerely hope that you choose a legitimate manufacturer when purchasing elevators, to avoid any worries about after-sales service.In winter, when working outdoors at heights below minus degrees Celsius, heating rest areas should be set up near the construction area if necessary. Heating equipment should be managed by dedicated personnel and attention should be paid to fire prevention.When the hydraulic lifting platform is working, the load cannot exceed its rated load. When it is raised to a certain height,Remember not to overload,AnkrajElevator manufacturer, overload is the root cause of many faults.. The hydraulic oil enters the upper end of the hydraulic cylinder through the explosion-proof electromagnetic directional valve, and the return oil from the lower end of the hydraulic cylinder returns to the oil tank through the balance valve, throttle valve, a balance valve and balance circuit are installed on the return oil circuit to maintain pressure and ensure that the descent speed is not affected by changes in heavy objects. The throttle valve regulates the flow rate and the lifting speed. To ensure safe and reliable braking and prevent accidents, a hydraulic one-way valve, also known as a hydraulic lock, is added to ensure safe self-locking when the hydraulic pipeline bursts. Install an overload sound alarm to distinguish between overload or equipment failure.When using hydraulic elevators, which not only extends the service life of the hydraulic elevator, but also enables it to exert greater power during operation. Of course, hydraulic elevators also have their own regular repair times and protection methods: regular protection (carried out per shift).