KavanaPipeline pump bodyarea covered

　　 strip the outer layer of the cable to expose the copper wire for to mm, gradually thin the rubber near the wire core, wipe the wire core with alcohol (or hydrochloric acid), wrap the insulation layer and sheath layer, pumping water up high. However, once the pump can not absorb water, the equipment is shaped like a decoration, so what is the reason for this situation? How to solve it?Kavana,　　How to prolong the service life of the submersible sewage pump Replace the sealing ring: after long-term use in the sewage medium, the gap between the impeller and the sealing ring may increase, so it should be replaced in time.　　If the pressure in the local area is equal to or lower than the vaporization pressure corresponding to the water temperature in the flow process, the water will vaporize there and form many small bubbles mixed by steam and gas. The cavitation phenomenon is due to the bubble action when these small bubbles flow from the low-pressure area to the high-pressure area in the water pump,Mount Gambier,　　Promote the continuous expansion of the sales network group.　　 Before starting the submersible slurry pump, the rotor of the rotating pump shall be smooth and even, the outlet sluice valve shall be closed, and water shall be injected into the pump to ensure that the pump is full of water without air.　　 If the pump is equipped with a vacuum gauge or pressure gauge close the cock connected with the submersible slurry pump before starting the motor, open it after the speed is normal, and then gradually open the outlet sluice valve. If the flow is too large you can properly turn down the gate valve for adjustment. Otherwise, if the flow is too smallOpen the gate valve.

　　How to avoid this situation when the equipment is in use.　　The slurry tip of this series is a horizontal slurry pump, which is divided into ah series: the overflow part is made of high chromium alloy and AHR series: the overflow part is made of natural rubber. It is a double pump casing structure, which is made of gray iron outside the casing, and the lining is professionally called sheath, which is made of high chromium alloy. If AHR series　　When the water pump is driven by electricity or diesel engine, its impeller (like an electric fan) rotates wildly, thus forming a vacuum in the impeller. In this way, the atmospheric pressure will move the water pressure to pump water. In fact, from a al point of view, it is to convert electrical or chemical energy into gravitypacking,　　Wheel, which are wear-resistant, corrosion-resistant,KavanaISG single stage vertical pipeline pump,KavanaAh slurry pump, non clogging,KavanaSingle stage slurry pump, and have strong sewage discharge capacity, and can effectively pass through large solid particles. It is not limited by suction range, with high slag suction efficiency and more complete desilting. There is no need to equip auxiliary vacuum pump, and the investment is lower.　　 If the pump is equipped with a vacuum gauge or pressure gauge, close the cock connected with the submersible slurry pump before starting the motor, open it after the speed is normal, and then gradually open the outlet sluice valve. If the flow is too large, if the flow is too small,Open the gate valve.　　The high-efficiency slurry pump has three characteristics: first, the slurry pump has high operation efficiency and low loss.

　　Water flow into the bearing damages the bearing.High value,　　Generally speaking, the above two cases are the case that the slurry pump does not absorb water. The solutions are also introduced. I believe that people can deal with this problem in time. However, if the problem is serious, you must not adjust it at will. At this time, you should find a professional　　 allowable maximum outer diameter of downhole part of pump mm　　Some corrosive pastes containing crystals can also be transported. In the application range of slurry pump, about % are used in concentrators in the mining industry. Due to the poor working conditions of primary ore dressing, the service life of slurry pump in this section is generally low. Of course, different minerals, abrasionKavana,　　Through the introduction, we learned that the submersible slurry pump can be used to transport slurry when it is used at ordinary times. The relationship between its special structure is very close, but in fact, it also needs to be used in a correct way when it is used at ordinary times. Only in this way can　　Will be scrapped. In addition, since the length of the long shaft is generally fixed, the installation and use of the slurry pump submersible are troublesome and the application occasions are limited. It is normal to use the equipment for a long time, for example, when the submersible slurry pump is used at ordinary times, air holes usually appear　　 The difference between the vertical slurry pump and the submersible slurry pump The working position of the vertical slurry pump is different. The vertical slurry pump is partially immersed in the pit and cannot be completely immersed in the liquid level. The submersible slurry pump can be completely immersed (including the motor part) below the liquid level; Use of motor for vertical slurry pump