San JoseCorrosive pipeline pumpHow is it saved

　　 Dust and oil stains on the motor reduce the heat dissipation capacity of the equipment and cause the equipment temperature to rise.　　 To ensure the efficient operation of the submerged slurry pump, the clearance between the impeller and the front guard plate must be adjusted regularly to keep it between (.-mm). In addition to monitoring the flow and pressure during the operation of the pump, the motor shall not exceed the rated current of the motor. Monitor oil seal and bearing at any timeSan Jose,　　Is the submersible sewage pump a submersible pump or a sewage pump QW (WQ) submersible non clogging sewage pump QW (WQ) submersible non clogging sewage pump: the pump adopts a unique single or double blade impeller structure, which greatly improves the sewage passing capacity and can effectively pass through times the fiber material and diameter of the pump diameter　　Stability and reliability of seals between pump bodies.Slough,　　 Impeller protection in order to ensure the operation of the submersible slurry pump, it is necessary to timely adjust the clearance between the impeller and the front guard plate. When adjusting the impeller clearance,San JoseZD slurry pump, first stop the pump, loosen the bolts pressing the bearing box, loosen the adjusting nuts, make the bearing components move forward,San JoseBooster pipeline pump, and roll the shaft by hand to press the　　If the pressure in the local area is equal to or lower than the vaporization pressure corresponding to the water temperature in the flow process, the water will vaporize there and form many small bubbles mixed by steam and gas. The cavitation phenomenon is due to the bubble action when these small bubbles flow from the low-pressure area to the high-pressure area in the water pump, clean the part to be bound with alcohol again and wipe it dry.

　　Do not exceed the rated current.　　. Generally, the moisture absorption section exceeds the suction section of the pump (the pump head is damaged). When the breathing tube passes through the pipe, the axial force cone tube shall be selected.　　If the water leakage is serious,San JoseISG single stage vertical pipeline pump, the broken pipe shall be dismantled and replaced. Lower the lift and press the nozzle of the water pump into the water for .m.Direct material,　　Circumference. In the application of slurry pump, we must pay attention to reasonable design, correct calculation and appropriate type selection, which are very important. In addition to the main wheel, a set of stirring impeller is added at the bottom of the product, which can spray the precipitated slag into a mixture of water and solid particles　　 The bus voltage where the motor is located is V. Due to the uneven cable voltage drop and load distribution, it is also possible that the temperature is too high due to the low voltage of the water pump.　　Strong strength and other advantages. It is widely used as a sealing device for various pumps. Place a water seal ring at the bottom of the packing box, and then place the filler.

　　Causes: there is air or gas accumulation in the water inlet pipe of the pump, or the bottom valve is not closed tightly, the water supply is not satisfied, and the gate valve or flap valve is not closed tightly.Latest quotation,　　Avoid airborne sound transmission; Ensure the airtightness of machine room doors and windows. The water pump is equipped with a sound proof cover, and an exhaust fan is added inside the cover to ensure the ventilation of the equipment. At the same time, the inlet and outlet of the sound proof cover are equipped with silencing equipment. A vibration isolation platform is installed at the bottom of the water pump for foundation vibration reduction to isolate the vibration generated during the operation of the water pump　　I would like to talk with you about the problems that should be paid attention to when using deep well pumps.　　Submersible slurry pump Use ultrasonic method to detect whether there is cavitation in the submersible slurry pump. This method is often convenient for re detection. Even if there is some noise in the surrounding environment, it will not affect the detection results. Therefore, many pumps often have better measurement results when in use.San Jose,　　The slurry pump of underground pump can also work normally.　　The production department has to spend a lot of money to maintain and update the pump every year. The pumps made of cast iron, bronze, stainless steel, titanium alloy and other materials used in China&#;s mining chemical and water conservancy projects on the Yellow River are prone to wear, which can be replaced without disassembling the slurry pump.