Compastra asuyaHH slurry pumpWhat are your connection methods

　　If the shaft seal is not properly selected,Compastra asuyaQuotation slurry pump, it will not only require frequent maintenance during operation, but also leak a large amount of transmitted liquid.　　Submersible slurry pump shaft seal type: packing, packing and auxiliary impeller seal, mechanical seal, etc.Compastra asuya, but improper use and maintenance will lead to submersible sewage.　　Let the medium containing some solid particles generate a certain flow rate, so that the equipment can drive the solid to flow when it is in use, so that the slurry can be transported. In terms of the principle of the submersible slurry pump, it is actually quite simpleHerentals,　　If the pressure in the local area is equal to or lower than the vaporization pressure corresponding to the water temperature in the flow process, the water will vaporize there and form many small bubbles mixed by steam and gas. The cavitation phenomenon is due to the bubble action when these small bubbles flow from the low-pressure area to the high-pressure area in the water pump,　　If the shaft seal is not properly selected,Compastra asuyaSmall deep well pump, it will not only require frequent maintenance during operation, but also leak a large amount of transmitted liquid.　　Submersible pump is a common water lifting equipment for deep wells. During operation, the whole machine intrudes into the water to extract water from the underground to the surface. It is commonly used for domestic water, mine rescue, industrial cooling, farmland irrigation, seawater lifting, ship load adjustment, landscape fountains, etc. Submersible pump is generally divided into clean water submersible

　　 Next, the fixing nut on the shaft shall beOK or not? so that it is convenient for us to disassemble the bearing parts; When the shaft is pulled out from the suction section lock ring and other parts need to be installed.　　 absorb fly ash and slime from various power plants.　　The first stage impeller of the pump is disassembled; It is also necessary to screw down the connecting nut between the water absorption section and the bearing body and the bolt on the bearing pressure connection,　　To repair the equipment. Submersible slurry pump is a machine used to transport liquid. It can be divided into many types according to different transport media. Then,Compastra asuyaVortex pump and pipeline pump, when transporting some media with special properties, the equipment will be treated with corrosion-resistant and wear-resistant process. Only in this way can the equipment be improved　　Therefore, the stator winding will be burnt out due to excessive temperature rise.　　When using the submersible slurry pump, we should do a good job in all aspects of commissioning and precautions. We also need to do a good job in protecting the equipment parts and some parts of the motor. Only in this way can we avoid the impact of water and other impurities entering the motor

　　 Dust and oil stains on the motor reduce the heat dissipation capacity of the equipment and cause the equipment temperature to rise.Work courses,　　It needs to be replaced in case of damage, swelling and deformation, insufficient spring pressure, breakage, etc.　　In order to meet the use requirements of slurry pumps in different industrial fields and working conditions, we have continuously carried out research development and improvement, so that we have different series, each series has a variety of specifications and models, and different series of products have different performance and s. Let&#;s learn about it below　　 There may also be mechanical failure of the pump, such as serious damage to the bearing of the pump, so that the bore will be 'swept' when the stator and rotor rub against each other, or the impeller will be stuck due to impurities such as water and grass when the pump pumps waterCompastra asuya, lift the submersible slurry pump and move it to the adjacent position of the previous sand pumping place to continue pumping sand, so as to move the sand pumping place back and forth for sand pumping, so that the sand pumping area in this area forms a honeycomb,　　The above introduction is about the cause ysis of the overload of the slurry pump. When we find these conditions when using the pump, we can check whether these reasons are the above. This is also a reminder that we need to maintain the pump during normal use. latent　　Cavitation of the pump is caused by water evaporation of the pump. The main cause of water evaporation is related to temperature and pressure. Under a certain pressure, when the temperature rises to a certain value, the water begins to vaporize and change from liquid to gas. On the contrary, at a certain temperature, the pressure drops to