Pachuka40Cr precision alloy tubeInstructions for industry norms

I-beam is divided into ordinary I-beam and light I-beam. The specification of hot rolled ordinary I-beam is -#. The specification of hot-rolled flexible I-beam supplied through agreement between the supplier and the buyer is -#. I-beam is mainly used in building structure, vehicle manufacturing, other industrial structures and fixed panels and cabinets. I-beam is often used together with I-beam. Hot stamping. Fix the plan product workpiece or preformed vacancy on the rotating journal, with the wheel working pressure vacancy radial wheel. After one or several solutions, there can also be a variety of methods for the whole process of hollow thick wall rotating body products. Products manufactured by high-precision processing method have excellent physical properties, specification scope, mold shell and software requirements, which are very simple, very easy to be replaced, and relatively low product cost. The processing time is not long enough, the processing capacity is not high, the total length of processing pipeline is limited and the size of machinery and equipment is generally short.Pachuka, I-beam is an I-shaped section steel. The inner surface of the upper and lower flanges has an inclination, generally :, which makes the outer flange thin and the inner flange thick. Therefore, and it is difficult to give full play to the strength characteristics in application. Although the thickened I-beam has also appeared in the I-beam market, the structure of the I-beam has determined its torsional performance.Salamanca,Pachuka20# seamless pipe manufacturer,Because the section size of ordinary I-beam and light I-beam is relatively large and narrow, the moment of inertia of the two main shafts on the section is quite different, which limits its application range. I-beam shall be selected according to the requirements of design drawings. In the structural design, the use of I-beam should be reasonably selected according to the mechanical properties, chemical properties, weldability and structural size of I-beam.Generally, the process of pickling and passivation will be carried out for alloy pipes, but the alloy pipes after pickling and passivation are very easy to rust. Therefore, the way to find a solution to wiredrawing corrosion is 'grinding and polishing'. Due to grinding and polishing, there is no harm to carry out hot galvanizing in the middle and later stage.H-section steel belongs to high-efficiency and economic cutting profile (other cold-formed thin-wall section steel, profiled steel plate etc.). Due to the reasonable section shape, they can make the steel give more play to its performance and improve the cutting capacity. Different from ordinary I-type, the flange of H-section steel is widened, and the inner and outer surfaces are usually parallel, so it is convenient to connect with other components with high-strength bolts. Its size composition is reasonable,Pachuka180 seamless pipe 1m, series and models are complete, which is convenient for setting

Plan scheme : Martensitic chromium alloy pipe and chromium alloy pipe with Cr composition exceeding %,PachukaHow much is a 2-inch galvanized pipe, without high carbon steel and high chromium alloy pipe. The aqueous solution contains % sodium cyanide % ~ % (volume ratio), and the solution time is min.Galvanized pipe has excellent corrosion resistanceSome applications of I-beam:Market trend,When it is used for ground heating and hot spring transportation, it can meet the requirements of refrigeration and achieve the practical effect of less damage. It is applicable to water conservancy engineering, mining and other industries to meet the provisions of cold, cold and corrosion prevention. In addition, the chemical raw material transmission pipeline has a wide indoor space.Alloy pipes can be used for heating (cooling) projects.In order to make the steel pipe workpiece have the required mechanical, physical and chemical properties, in addition to the reasonable selection of materials and forming processes, heat treatment process is often essential. Steel is the most widely used material in the mechanical industry. The microstructure of steel is complex and can be controlled by heat treatment. Therefore, the heat treatment of steel is the main content of metal heat treatment. In addition, aluminum, copper, magnesium, titanium and their alloys can also change their mechanical, physical and chemical properties through heat treatment to obtain different service properties.

Alloy pipe is a very important way and type of seamless steel pipe. Its use is relatively common. It is widely used in various engineering projects, house construction and building decoration. Its fracture will always be found in the production, manufacturing and key marketing of alloy pipe, That is, many stages of production and processing are not done well. Another is that the seasoning is not enough and the proportion of chemical molecules is wrong. There are all reasons.Quality Assurance,Whether I-section steel is ordinary or light, because the section size is relatively high and narrow, the moment of inertia of the two main axes of the section is quite different, so it can only be directly used for members bent in the plane of their web or form lattice stressed members.Galvanized pipe features:I-beam can only be used for beam, while H-beam can be used for load-bearing column of structure.Pachuka,Metallization: refers to the process of penetrating metal atoms into the surface layer of alloy steel pipe. It is to alloy the surface layer of steel so that the workpiece surface has the characteristics of some alloy steel. Aluminizing chromizing, siliconizing and so on are commonly used in production.I-beam: national standard * what is the wall thickness of I-beamFunction of I-beam: where is I-beam mainly used?