GibraltariansHH slurry pumpWhat aspects should be paid attention to in the operation of

　　 When the slurry pump fails to absorb water during operation,GibraltariansSelf priming slurry pump wholesale, it may also be because the bottom valve is not opened. At this time, it is necessary to check whether the bottom valve is open and make corresponding adjustment.　　 Prepare tools and materials: a set of metric box / open-end wrench, bearing puller (commonly known as triangle puller), magnetic dial indicator, outside micrometer, caliper, feeler gauge, square ruler, copper bar, screwdriver with handle hammer, clean kerosene V-shaped irons of the same specification, oil basin, etc.Gibraltarians,　　If there is a gap in the actual work, if the pipeline can not absorb water normally, it is necessary to find out whether the model of the pipeline pump can have the self-priming , and then check the cause of the abnormal suction range of the pipeline pump and solve it.　　Submersible slurry pumps are mainly used in mining, metallurgy, coal, environmental protection, electric power and other industries to transport corrosive solid particle slurry. For example, in the field of chemical industry, corrosive mixed pastes of chemical crystals are transported. Electric ash removal, coal washing plant slurry transportation, etc. Submersible slurry pump bladeTagurgon, the secondary and tertiary pumps can be started successively until the final stage pump. After all the series pumps are started, the outlet valve of the final stage pump can be gradually opened. The speed of opening the valve should be controlled by the fact that the pump does not vibrate and the motor of any stage does not exceed the rated current.　　 The pump body (can not) bear the pressure from the outlet pipeline system. The standby pump in the warehouse should rotate (/ times a week to make the shaft bear the load and external vibration evenly. The belt CR drive is that the motor is on the (right) side of the pump from the inlet of the pump.　　 Why does the demand for submersible slurry pumps increase greatly? From the perspective of market demand, it has a rapid development momentum. The main reason is that the above-mentioned use is convenient and flexible; In addition, the application market of submersible slurry pump is also better than that of vertical pump

　　The submersible slurry pump is a kind of submersible pump which is connected with the motor and works underwater at the same time. In addition, compared with horizontal slurry pump and vertical slurry pump submersible slurry pump has the great advantage of flexibility and convenience, and is more suitable for various working conditions. The important technical points of submersible slurry pump are its motor and　　 The WQ submersible sewage pump has compact overall structure,GibraltariansCorrosive pipeline pump, small volume, low noise, remarkable energy-saving effect and convenient maintenance. It can work by diving into the water without building a pump house, greatly reducing the project cost.　　 The gas inadvertently entered in the equipment is discharged and good sealing performance is ensured.analysis,GibraltariansCarbon steel explosion-proof pipeline pump,　　After the submersible slurry pump leaves the factory, there is generally only outgoing cable, and the user needs to connect it separately during installation. If the connection is wrong, it will seriously affect the normal operation of the pump, so we should follow the correct steps to connect.　　Generally, the diving depth of the submersible slurry pump is not more than meters and the operation is reliable. Why not more than meters? This is the crucial technical point of the submersible slurry pump, because the current sealing technology in China is more than meters, not because the slurry pump has a problem, but because　　The balance ring is also disassembled; Then remove the last stage impeller and the key back, and the middle section including the guide vane; in addition, remove the impellers, middle sections and guide vanes at other levels in the same way until the submerged slag slurry

　　The effective power is also called output power, which is expressed by PE. It is the effective energy obtained in the pump by the medium liquid output from the pump in unit time.Packaging strategy, such mechanical faults will cause the stator winding of the pump to be burnt out.　　The harm and avoidance of the reverse rotation of the slurry pump impeller the reverse rotation of the slurry pump impeller may cause the slurry pump impeller to fall off at least, or cause the damage of the whole pump at most. The reverse rotation of the slurry pump impeller mainly has the following hazards: The slurry pump impeller falls off. The connection between the slurry pump impeller and the pump shaft is a one-way screw　　What is the order.Gibraltarians,　　Moreover, the leaked flammable, explosive and toxic liquid will cause fire, explosion and poisoning, and the consequences will be unimaginable.　　During adjustment, firstly loosen the support cover, then compress the nut, and then loosen the bearing seat. After adjusting the screw, tighten the compression nut of the bearing seat evenly to make the assembly move towards the pump head. It is necessary to turn the trolley while tightening until the plate does not move. Rotate according to the pump operation　　 To ensure the efficient operation of the submerged slurry pump, the clearance between the impeller and the front guard plate must be adjusted regularly to keep it between (.-mm). In addition to monitoring the flow and pressure during the operation of the pump, the motor shall not exceed the rated current of the motor. Monitor oil seal and bearing at any time