Hel BrownVertical slurry pumpCategory price correlation regression

　　After that, before starting again, check whether the impeller rolling is normal and whether the bearing assembly compression bolts are tightened, and then start the pump.　　Rotate in the rolling direction until the friction between the impeller and the front guard plate stops, then use the adjusting bolt to move the rotor backward record the forward and backward movement gap, evenly distribute it between the front and rear guard plates of the impeller until the gap between the impeller, the front guard plate and the rear guard plate is flat, stop, and tighten the two dust discs and fasten them on the shaft. adjustmentHel Brown,　　Clean up the silt and other obstructions in or around the water pump.　　 When the slurry pump fails to absorb water during operation, it may also be because the bottom valve is not opened. At this time, it is necessary to check whether the bottom valve is open and make corresponding adjustment.Pallin ,　　If the pressure in the local area is equal to or lower than the vaporization pressure corresponding to the water temperature in the flow process,Hel BrownWQ submersible pump parameters, the water will vaporize there and form many small bubbles mixed by steam and gas. The cavitation phenomenon is due to the bubble action when these small bubbles flow from the low-pressure area to the high-pressure area in the water pump,　　If there is a standby pump, it is better to use two pumps in turn. If the pump is stuck, the pump can only be repaired. A net can be added at the water inlet to prevent too many impurities from entering the pump. In this way, the probability of pump sticking will be much smaller!　　The submersible slurry pump can be used to transport a lot of media containing solid particles when it is used at ordinary times, the diameter of the impeller after cutting shall not be less than % of the diameter of the standard impeller, otherwise the of the pump will have a very adverse change. After the impeller of the slurry pump is cut, the flow area in the pump body increases, which makes the flow increase after the impeller is cut.　　And multi-stage slurry pump; Fourth, the types of slurry pump can be divided from the pump shell of slurry pump: single shell slurry pump and lecture slurry pump; Let&#;s talk more about the model classification of slurry pumps: such as ah, HH, m slurry pumps. These series of slurry pumps can be collectively referred to as fractional series slurry pumps because these types　　The non service life of the equipment is not as long as possible. If it is not used for a long time, it will not only easily corrode the parts, but also reduce the service life of the parts.Quality assurance　　Stop, then tighten the bearing seat, press down the nut, and fix the axial position of the rotor. The latter submersible slurry pump uses a barrel support,Hel BrownVertical heavy-duty slurry pump, which generally does not need to adjust the impeller clearance. Therefore, if there is a problem with the clearance in the future use, loosen the support clamp first, let&#;s learn about the packaging and sealing method of the equipment: packing sealing is very common in submersible slurry pumps. This method has good sealing performance, is easy to use, and effectively reduces the wear of the host and anti vibration kinetic energy　　It will burn out. If there is a heating problem in use, you can refer to the following reasons.

　　Therefore, when the pump temperature is too high, you don&#;t need to panic. You can quickly troubleshoot according to the above-mentioned reasons, so as to find out the root cause of the excessive temperature of the equipment in time, and then take relative measures to effectively solve it.offer　　 Then replace the pulley and pump cover plate and tighten the fixing nuts.　　 transmission device type (gearbox transmission, V-belt transmission)　　The purpose is to inject liquid higher than . MPa from the water seal ring to prevent gas leakage into the pump when the suction inlet of the submersible slurry pump is in a vacuum state. When the water pressure in the pump is higher than . MPa, the sealing fluid .-. MPa higher than the pressure in the pump can be injected to seal and reduce leakageHel Brown,　　The slurry pump of underground pump can also work normally.　　The pump can often be selected according to the specific requirements of lift, flow and liquid delivery. The flow range of the delivered liquid is - L / s, the pressure range is .- MPa, and the diesel engine speed range is - rpm. Features: water pump, high automation and performance　　After that,Hel BrownSplit vertical pipeline pump, before starting again, check whether the impeller rolling is normal and whether the bearing assembly compression bolts are tightened, and then start the pump.