ministerVertical centrifugal slurry pumpWelcome to inquire

　　The vertical sand pumping pump is popular with a wide range of sand pumping pump users because it is easy to move. This equipment is made of high-tech endurance data. Its service life has been greatly improved, the cost has been reduced, and the income has been increased.　　 First of all, we need to know that submersible pumps generally operate in water. In fact, most of the pumps are suitable for conveying some relatively clean media, one of the media conveyed by sewage pumps mayminister,　　 observation method: people can visually observe whether the machine parts on the submersible slurry pump are loose, cracked and damaged. Through comprehensive ysis of various observation information, fault location fault degree and fault cause.　　Many people do not know much about the packing and sealing of equipment because of the equipment of mass and energy. Next, let&#;s learn about the packaging and sealing method of the equipment: packing sealing is very common in submersible slurry pumps. This method has good sealing performance is easy to use, and effectively reduces the wear of the host and anti vibration kinetic energyHodonin,　　Its main features are as follows: the whole machine is a dry-type motor pump structure. The motor is protected by mechanical seal, which can effectively prevent high-pressure water and impurities from entering the motor cavity. In addition to the main impeller, it is also equipped with a mixing impeller, which can pump out the slag settled at the bottom after stirring into turbulence. impeller　　Do a good job of fixing to avoid the motor falling into the water and directly scrapping.　　Second,ministerVertical centrifugal slurry pump, the service life of the flow passage parts of the pump is relatively long, saving production costs.

　　The submersible slurry pump is developed to adapt to the increasingly complex working conditions and facilitate the use of users. Its use mode is more flexible. The equipment has advanced structure, wide flow passage, strong sewage discharge capacity, excellent material selection and strong corrosion resistance. Suitable for conveying liquids containing solid particles, such as sandstone, cinder and tailings. So what are the requirements for its work? Let&#;s understand briefly.　　 total depth of well or pool M　　 Precautions for disassembly of submersible slurry pump Before disassembling the filter press, make sure that the liquid in the submersible slurry pump is completely discharged. If the rotor is disassembled,ministerSubmersible sewage pump, drain the lubricating oil in the rotor bearing housing. If the newly added oil is stored, it should continue to be used after maintenance. Do not dump it directlyproperty right,　　Many people do not know much about the packing and sealing of equipment because of the equipment of mass and energy. Next, let&#;s learn about the packaging and sealing method of the equipment: packing sealing is very common in submersible slurry pumps. This method has good sealing performance, is easy to use,ministerBaigang deep well pump, and effectively reduces the wear of the host and anti vibration kinetic energy　　It is longer and saves production cost. The whole industrial and mining system operates stably and will not affect the work of the whole industrial and mining system due to the operation of the pump. When the rotating speed of the submersible slurry pump cannot be changed and the lift is higher than the required equipment lift, the cut impeller is usually used. The cut is　　In fact, it can only be opened or closed, and the action time when opening and closing is relatively short.

　　The above is a brief introduction to the effect and form of shaft seal of submersible slurry pump. Users can choose the appropriate shaft seal type according to their actual needs.new product,　　 Another possibility is that the gas is sucked in when the pump is in use.　　There is no suction line. As the water storage tank is not deep enough and the suction pipe of the water pump is not deep enough, the inlet pipe of the water vortex is not deep enough. Water with a lot of gas. Destroy all normal water Self-priming pumps. To ensure sufficient depth of digestion and absorption of low watermark water. At that time, the depth was .~lm, and it was impossible to　　 Next, the water seal lock ring and other parts need to be installed.minister,　　 The fan speed of the water pump is too low, and the air pressure and air volume are relatively small, so the heat cannot be dissipated.　　Vertical slurry pump is an early product. Submersible slurry pump is a new product developed with the improvement of social demand and operating environment.　　This phenomenon shows that the failure of the pump is not only a material problem, but also reminds the pump designers and producers that in addition to good working conditions, the pump should also have good corrosion resistance, high reliability and long service life. The pump shall be designed in addition to the conventional design method of fluid mechanics