CHABASSubmersible slurry pumpThe price is more favorable

　　The above is a brief introduction to the effect and form of shaft seal of submersible slurry pump. Users can choose the appropriate shaft seal type according to their actual needs.　　Line direction pay attention to the direction of rotation. Then loosen the original compression nut of the bearing box of the slurry pump of the submersible pump, tighten the adjusting screw of the bearing box evenly, and then move the rotor assembly towards the motor. Then it is necessary to check the clearance with a feeler gauge δ, When δ= A (. ~ mmCHABAS,　　During the long-term overload operation of submersible sewage pumps there are many cases of sudden abnormal failures of submersible pumps. Among them, there are some common obstacles, such as the submersible pump cannot be started after it is powered on, or the motor speed cannot be started after the submersible pump is started. A very small wait　　The application of pumps involves all aspects of work and production, and the types of pumps are also diverse. Some of the same pump have several names, and some of the names are very similar, which makes it difficult to distinguish. Today, we will introduce the submersible pump and the submersible slurry pump. Is there any difference between the twoKromezhesh,　　 When stopping the operation of the submersible slurry pump, close the cock of the vacuum gauge and pressure gauge and the gate valve on the water outlet pipeline, and After that,CHABASSubmersible pump can pump sewage, cut off the power supply of the motor. If the temperature of the environment is low, open the square plug at the lower part of the pump body to remove the remaining water to avoid frost cracking. During operation, and the quantity of calcium base grease used for lubricating oil bearing shall be the same as that of the bearing body　　 We also need to make choices according to local conditions when we make purchases at ordinary times. For example, the head of the centrifugal pump itself is relatively high, but its water output is not very large when it is used, but the water seal may be damaged due to faults after being used for a period of time. Let&#;s learn how to replace the water seal.

　　 There may also be mechanical failure of the pump such as serious damage to the bearing of the pump, so that the bore will be 'swept' when the stator and rotor rub against each other, or the impeller will be stuck due to impurities such as water and grass when the pump pumps water　　 When the electric pump is not in use, take it out of the water and do not immerse it in the water for a long time, so as to reduce the chance of the motor stator winding getting damp and increase the service life of the electric pump. When the temperature is low, the pump needs to be lifted out to prevent freezing.　　The balance ring is also disassembled; Then remove the last stage impeller and the key back, and the middle section including the guide vane; in addition, remove the impellers, middle sections and guide vanes at other levels in the same way until the submerged slag slurryMarketing Department, which can offset part of the axial force and prolong the service life of the bearing.　　.　　Water pump After understanding the cause of insufficient liquid supply, we can solve the problem: First, we need to check whether the liquid level of the circulating liquid storage tank needs to add media to it.

　　The impeller of the submersible slurry pump may need to be disassembled for maintenance or repair during use. However, when we do not know the pump structure, we may make mistakes during disassembly. Let&#;s take a look at the correct disassembly of the impellerDesign brand,　　 The fan speed of the water pump is too low,CHABASPipeline pump, and the air pressure and air volume are relatively small, so the heat cannot be dissipated.　　 Check the water pump: it is possible that the selection of the water pump is not matched with the motor, which makes the temperature of the motor too high after long-term operation; It is also possible that the working time exceeds the specified working time of the motor. At this time, the use time and times should be strictly limited, the correct thermal protection should be selected, and　　 We must choose to consider the actual use situation when making the selection because there will be some difference between the marked head when using and the head when using. This is because the pipe itselfCHABAS,CHABASAh slurry pump,　　 Another possibility is that the gas is sucked in when the pump is in use.　　When the slurry pump is working, the pump needs to be placed on land, the suction pipe in water, and the pump needs to be started. Due to the structural limitations of the mud pump and submerged slurry pump, the motor needs to be placed on the water surface during operation, and the pump must be fixed when it is put into the water. Otherwise, the motor will fall into the water　　In this way, a smooth surface can be formed on the surface.