Selni mostCentrifugal slurry pumpFocus on manufacturers

　　Stop, then tighten the bearing seat, press down the nut, which generally does not need to adjust the impeller clearance. Therefore, loosen the support clamp first, and say that the nut is loose　　It is an auxiliary means of on-site monitoring. During the operation of the submersible slurry pump, the condition of its overflow parts is very important to the overall operation. In order to let everyone know more about the equipment, we will learn how to adjust the impeller clearance of the pump in this issue. I hope it will help you.Selni most,　　 Before using the pump, carefully check whether the cable is damaged, whether the fasteners are loose or fall off, and whether the pump is deformed or damaged during transportation, storage and installation.　　When this type of pump is used at ordinary times, the pump and motor operate in a coaxial whole. When it runs, the motor shaft will drive the impeller of the pump to rotate, and then at this time, the rotating force can be brought to the medium, so thatWitten,　　The of descending axial force can be used for slurry transportation in power plants, hydraulic and other professions; The mechanical seal is tight and reliable, and the leakage probability does not exceed drops /min which is mostly used to transport flammable, explosive, toxic, strong corrosive and valuable liquids or materials with high temperature, high pressure and low temperature.　　Some impurities will entangle the impeller, so generally, so there is no need to worry about getting stuck in the process of transporting sewage.　　Slurry pump Inappropriate model is selected when selecting the pump. In actual use, when the load conditions do not match the model of the slurry pump, for example, the pump lift used is too high or too low, which will lead to overload, so we are selecting the pump

　　When the submersible slurry pump works, the pump needs to be placed on land, the suction pipe needs to be placed in water,Selni mostHorizontal non clogging sewage pump, and the pump needs to be started. Due to special structural requirements, when the slurry pump motor is submerged in the water, the slurry pump and submerged slurry circulating pump need to be placed above the water surface, so they need to be fixed otherwise the motor will fall into the water　　That is, first, check whether the equipment operation noise is reasonable; second,Selni mostWQ submersible sewage pump, check whether the alarm unit has leakage and overheating alarm signals; third, check whether the vibration of the guide rod is normal; fourth record the flow and current of the water pump operation. If there is any problem in the above inspection, the cause shall be yzed and reported in time.　　 for screws that are too tight or rusted for a long time, the nut can be lubricated with kerosene prepared in advance,Selni mostSplit vertical pipeline pump, or the nut can be gently knocked with a wooden hammer and then removed. This method can also be used in slurry pumps and other places.Development Curriculum,　　So it is called: submersible slurry pump.　　 In addition, the noise method directly detects the noise of the equipment in the detection process, but this measurement will also be affected by the surrounding noise, so in fact this measurement is not very accurate.　　The purpose is to inject liquid higher than . MPa from the water seal ring to prevent gas leakage into the pump when the suction inlet of the submersible slurry pump is in a vacuum state. When the water pressure in the pump is higher than . MPa, the sealing fluid .-. MPa higher than the pressure in the pump can be injected to seal and reduce leakage

　　 First of all, most of the pumps are suitable for conveying some relatively clean media, and their impellers are generally in a closed state. However, one of the media conveyed by sewage pumps mayHow much does it cost?,　　When the water level reaches, the frequency of the frequency converter drops, and the slurry pump operates at a low speed. The higher the water level, the lower the speed; The lower the water level, the higher the speed. At the same time, the water level signal is transmitted to the control cabinet so that the operators can timely understand the liquid level. Through this control, the circulation in the slag slurry pool is basically unchanged　　Consider the vertical separation level of the tail equipment.　　Rotate in the rolling direction until the friction between the impeller and the front guard plate stops, then use the adjusting bolt to move the rotor backward, record the forward and backward movement gap, evenly distribute it between the front and rear guard plates of the impeller until the gap between the impeller, the front guard plate and the rear guard plate is flat, stop,　　Moreover, because the length of the long shaft is generally fixed, it is often troublesome to install it. Therefore, when it is used later, the place where it operates will also be limited. If the equipment will　　In the application of pumps, the first thing we think of is water. Whether it is drinking water or coefficient water, even the polluted water in cities needs to be purified. All these require its equipment to provide services for us. Without pumps, our basic survival is a problem.　　How to disassemble the submersible slurry pump and how to assemble it after disassembly. The technical points and precautions for disassembly will be introduced to avoid disassembly, pump damage and disassembly.