The wear resistance, fracture toughness, impact toughness and bending strength under different process conditions were compared, and then the heat treatment process of GCrMo was determined. Development and application of ZYS- bearing damping and antirust oil. Bearing is a new type of multial damping and antirust oil. It takes refined mineral oil as the base oil and is equipped with various additives such as antirust and antifriction. Through comparison test matching test with lubricating grease and user test, it is proved that ZYS- bearing damping and antirust oil has outstanding damping effect and good antirust lubrication performance.As shown in the name, I-beam is an I-shaped section steel. The inner surface of the upper and lower flanges has an inclination, generally :, which makes the outer flange thin and the inner flange thick. Therefore, the section characteristics of I-beam in the two main planes are very different, and it is difficult to give full play to the strength characteristics in application. Although the thickened I-beam has also appeared in the I-beam market the structure of the I-beam has determined its torsional performance.Heidelberg,The preparations for the construction of high-speed reinforcement mesh include the preparation and inspection of raw materials, the inspection and acceptance of the lower layer of the pavement, and the preparation of construction equipment and engineering machinery.I-beam whether ordinary or light, can only be directly used for bending members or lattice members on its Web because of its large and narrow section size and large moment of inertia difference between the two main axes on the section. It is not suitable for axial compression members and flexural members perpendicular to the web plane, so its application range is very limited. I-beams are widely used in buildings and other metal structures.Kamwenge,Advantages of using I-beam: reduce maintenance cost, reduce downtime, improve equipment operation rate, reduce wear, reduce equipment capacity and increase power consumptionThe delivery length of I-beam is divided into fixed length and double length, and the allowable difference is specified in the corresponding standards. The length selection range of domestic I-beam is divided into -, - and - according to different specification numbers. The length selection range of imported I-beam is generally -.Application characteristics of I-beam:
C - section steel is reliable and stable in stress, can be accurately positioned, and is resistant to impact and vibration Moreover, and has a variety of C-section steel and size selection to ensure its flexibilityHonesty is the foundation,The high-temperature passivation treatment of alloy pipe is to obtain the passivation treatment film by heating in the heat treatment equipment. Before passivation treatment, the surface layer of parts must be removed to remove waste. At a higher temperature the passivation treatment film can be obtained according to the transformation temperature and time. The hue of passivation treatment film can refer to the annealing color of alloy pipe, and the main parameters of ambient temperature and time of heat treatment process can be selected. According to the pipe wall thickness, pipes made of relatively thin materials such as steel strip can be welded with high frequency, and some thin-walled pipes can be welded with shielding gas; Pipes with wall thickness more than mm can be welded by hand. Frame line crackHeidelberg,Defects of alloy pipe and solutions:Its heat sealing effect is remarkable. It can be directly buried immediately, but also reduce consumption, not occupy the natural environment, but also purify the environment. The transportation of gas can meet the requirements of long-distance transportation, meet the requirements of thermal insulation and cold protection, reduce heating equipment, unique and convenient installation, and reduce the construction cycle time of the project. On the whole, it is more convenient to use. It can also be used for the transportation of floor heating and hot springs.Because the section size of ordinary I-beam and light I-beam is relatively large and narrow, the moment of inertia of the two main shafts on the section is quite different, which limits its application range. I-beam shall be selected according to the requirements of design drawings. In the structural design, the use of I-beam should be reasonably selected according to the mechanical properties, chemical properties, weldability and structural size of I-beam.
Hui Cai Technology Co., Ltd. 2024-04-23 08:37:24 support 0 | be opposed to 0
Jinglong Times Clothing Company 2024-04-23 09:34:56 support 0 | be opposed to 0
Wei Ye Heating Equipment Company 2024-04-23 09:36:53 support 0 | be opposed to 0
The Group's state-owned assets management 2024-04-23 09:05:35 support 0 | be opposed to 0
Optical cable fittings 2024-04-23 08:54:14 support 0 | be opposed to 0