AtlantaElectric lifting platform Hydraulic lifting platformWhat are the specific hazards

attention should be paid to ensuring that the centerline of the reverse organization reducer is parallel to the centerline of the gear, and its meshing surface is not less than %. The meshing gap should be appropriate.If the circuit of the device is not disconnected or lowered, it is necessary to check the fuse for repair and replacement.Atlanta,What technical issues are required for the installation of hydraulic freight elevators? The installation of hydraulic freight elevators is actually quite complex. If you do not understand the equipment pictures designed by the elevator manufacturer and the detailed situation of the hydraulic freight elevator designed by the elevator manufacturer, installation errors may occur, leading to equipment failure of the freight elevator! When installing hydraulic freight elevators, it is necessary to accurately calculate the size of the pit. The guide rail hydraulic freight elevator is a freight elevator composed of chains, guide rail torque tubes, and other components, mainly driven by the chain to assist in the upward and downward telescopic lifting of the freight elevator. The pulleys at the four corners of the countertop should be fixed on the surrounding guide rails. The entire elevator equipment is installed on the wall,AtlantaLifting platform hydraulic pressure, and wall mounted installation is chosen to enhance the stability of the freight elevator. Choosing the appropriate wall size also requires careful planning.There is a phenomenon of self stopping when running up and down. Due to poor contact of the safety protection switch, it is easy for hydraulic cargo elevator manufacturers to cause this problem.ESPO,Due to damage to the gear pump of the lifting cargo elevator equipment and no pressure lifting. Replace the gear pump.The combined platform is often used in small workshops with small volume of goods. However, because this platform needs to complete two functions at the same time, it inevitably increases the distance of handling tools/vehicles in the workshop.Considering the oil level in the oil tank, when all hydraulic cylinders in the system are extended, the oil level in the oil tank should not be lower than the Z-low oil level, and when the oil cylinders retract the oil level should not be higher than the Z-high oil level. In fact, most manufacturers have noticed the above issues. The reason for the introduction is that most users can learn more about the equipment itself when using elevators, in order to facilitate equipment maintenance. Hydraulic cargo elevator manufacturers sincerely hope that you choose a legitimate manufacturer when purchasing elevators, to avoid any worries about after-sales service.

The manufacturer of hydraulic cargo elevators will tell you about the knowledge of specialized lifting platforms for unloading.There are two reasons for the sinking of the hydraulic cargo elevator table: on the one hand, the hydraulic pressure is flexible, and under high pressure or temperature, the volume will change, which is reflected in the lowering of the position on the table.The smoothness of the gearbox, gearbox, external meshing gears and hydraulic oil are all carried out according to the requirements in the smoothness table.Latest consultation,Do not use hydraulic lifting equipment with malfunctioning issues. The problem should be resolved before carrying cargo.The classification of lifting platforms is as follows: they are divided into mobile lifting platforms,AtlantaFixed electric hydraulic lifting platform, automatic lifting platforms, and sleeve type lifting platforms according to their different modes of movement.Hydraulic lift cargo elevators belong to high-altitude work equipment. Small shaking of the scissor type structure is normal, but excessive deviation is a symptom. It is necessary to find the cause and make correct judgments in a timely manner. Generally speaking, devices above this height begin to vibrate in different ranges. The vibration range depends on factors such as weight, lifting height and intensity of high-altitude operations.

The contact of the travel switch must be firmly opened and closed, and the contact crater should be polished in a timely manner.Quality recommendation,There are many reasons for unstable workbench descent,AtlantaElectric lifting platform Hydraulic lifting platform, such as overload, unstable support, severe eccentric load, hydraulic oil impurities, etc. In response to the above reasons, it can be solved by reducing the load, adjusting the center of gravity of the load, and replacing hydraulic oil wholesale for hydraulic cargo elevators.The hydraulic system of the fixed lifting platform of the hydraulic cargo elevator is equipped with anti fall and overload safety protection devices, and operation buttons can be set on each floor and the lifting platform workbench to achieve multi-point operation. There is air in front of the pilot valve of the elevator overflow valve noise overflow valve. The damping hole on the main valve core of the overflow valve is blocked by oil dirt, and the pilot valve and valve seat are matched without spring deformation or incorrect installation. The remote control port has excessive oil flow low or high hydraulic oil viscosity, and resonance occurs with components in the circuit. Troubleshooting: Strengthen sealing, repeatedly adjust the pressure, exhaust and clean the valve body several times, Make the damping hole unobstructed, repair or replace the spring, reduce the flow of the remote control port, replace the oil, and other components. The pressure setting of other components should not be similar to the pressure setting of the relief valve. . The noise of the elevator pipeline is usually caused by excessive dead bends or loose fixed sleeves in the hydraulic pipeline.Atlanta, There is air in front of the pilot valve of the elevator overflow valve noise overflow valve. The damping hole on the main valve core of the overflow valve is blocked by oil dirt, and the pilot valve and valve seat are matched without spring deformation or incorrect installation. The remote control port has excessive oil flow, low or high hydraulic oil viscosity, and resonance occurs with components in the circuit. Troubleshooting: Strengthen sealing, repeatedly adjust the pressure, exhaust and clean the valve body several times, Make the damping hole unobstructed, repair or replace the spring, reduce the flow of the remote control port, replace the oil, and other components. The pressure setting of other components should not be similar to the pressure setting of the relief valve. . The noise of the elevator pipeline is usually caused by excessive dead bends or loose fixed sleeves in the hydraulic pipeline.Do you know the classification of simple cargo elevator lifting platforms? The manufacturer of the hydraulic cargo elevator is here to inform you.Stability: The workbench should evenly withstand % of the MAX load capacity and be stable at the MAX elevation.