MontleyVertical centrifugal slurry pumpWhat factors do price common sense have to do with

it has a great impact on the impeller of the equipment itself. So how to detect whether the equipment has cavitation during use?　　The input quantity is related to many factors such as the rotating speed of the submersible slurry pump

　　For example, the bearing standard, the continuous working time, the number of stops and starts of the pump, the surrounding environment and the working temperature. Therefore, it is necessary to gradually accumulate the experience and add smooth oil in a reasonable and timely manner.Montley,　　It can be that there is water leakage in the pipe gasket, pipe or pump body. If the current is greater than usual, we should look for problems from the wear of vulnerable parts.　　 selection of flow: single suction pump or double suction pump shall be selected according to the flow; single suction pump or multi suction pump shall be selected according to the lift.Kilju,　　If there are sundries blocked, the pump will not be filled with water. When this happens again, and check the impeller. In case of damage or aging, it needs to be replaced in time,　　 First, screw down the bolts on the side bearing pressure cap, and then remove the nuts used for the connection between the three parts: discharge section, stuffing box body and bearing body; Then screw off the round nut on the shaft, and successively install the bearing inner race, bearing gland and retaining sleeve　　Do a good job of fixing to avoid the motor falling into the water and directly scrapping.

　　 strip the outer layer of the cable to expose the copper wire for to mm, gradually thin the rubber near the wire core, wipe the wire core with alcohol (or hydrochloric acid), and dry it naturally.　　During daily use, we can observe, listen to and touch the submersible slurry pump according to the above methods, so as to judge whether there is a fault and the fault part of the slurry pump, and deal with it in time if any fault is found.　　In addition, the sundries inside the pump body and impeller shall be cleaned. Then calibrate the pump shaft and motor shaft of the slurry pump to make them on the same horizontal line.Click to view,　　Rate.　　Circumference. In the application of slurry pump, we must pay attention to reasonable design, correct calculation and appropriate type selection,MontleyPipeline pump, which are very important. In addition to the main wheel a set of stirring impeller is added at the bottom of the product,MontleyCirculating hot water pipeline pump, which can spray the precipitated slag into a mixture of water and solid particles　　 The bus voltage where the motor is located is V. Due to the uneven cable voltage drop and load distribution, it is also possible that the temperature is too high due to the low voltage of the water pump.

　　 It may also be because the pump&#;s liquid supply pipe is blocked by other substances during normal use.Which one is better,　　 Pipeline layout: Firmly support the water pipe and drain pipe to prevent the force of the pipe from acting on the submersible slurry pump.　　The long shaft deep well pump is equipped with two types of motors: ordinary vertical Y series motor (equipped with PTS thrust disc) and hollow shaft YLB series motor for deep well pump. The insulation grade is divided into class B and class F. now,MontleyDeep well pump, with the progress of science and technology and the continuous development of products, YLB series has developed high-voltage, protection and other grades up to　　First, let&#;s talk about the familiar vertical slurry pumps. Here we refer to ZJL and SP submerged slurry pumps. Strictly speaking, the submersible slurry pump is also a vertical slurry pump, because its axis is basically vertical when it works but it can be completely immersed in water when it runs, so it is a good choiceMontley,　　 Next, the water seal, lock ring and other parts need to be installed.　　 It may be that the motor power of the water pump is too large, the working current is too large, and the heat generation is too large, resulting in the high temperature of the vacuum pump.　　 drainage and water injection with vacuum equipment: the self exhaust of centrifugal pump is the same as the negative pressure exhaust of vacuum pump, so the water ring vacuum pump is used for exhaust to achieve the of water inlet.