MilwaukeeSubmersible non clogging slurry pumpIdentification method of

　　 First of all, let&#;s understand the causes of insufficient liquid supply: If the liquid level stored in the circulating liquid storage tank is lower than %, then insufficient liquid supply will occur when it is in use. Or the pump adds too much lubricating oil, which leads to accumulation　　If the pressure in the local area is equal to or lower than the vaporization pressure corresponding to the water temperature in the flow process, the water will vaporize there and form many small bubbles mixed by steam and gas. The cavitation phenomenon is due to the bubble action when these small bubbles flow from the low-pressure area to the high-pressure area in the water pump,Milwaukee,　　 optimal water inflow of well m/h　　The premise of using this method is that the water gun must have sufficient flow during use, otherwise the effect of the submersible slurry pump may not be obvious.Larache,　　After that, the secondary and tertiary pumps can be started successively until the final stage pump. After all the series pumps are started the outlet valve of the final stage pump can be gradually opened. The speed of opening the valve should be controlled by the fact that the pump does not vibrate and the motor of any stage does not exceed the rated current.　　 Then reinstall the equipment on the engine and install the rubber hose.　　 Next, it is necessary to check the water seal. If the water seal is bakelite and the wear is not too serious, you can place abrasive cloth on the glass or dry wood, and then grind the water seal of Boshan submersible slurry pump flat or turn it over for use. However, if the thrust rubber water seal is used, when

　　 Precautions for disassembly of submersible slurry pump Before disassembling the filter press, make sure that the liquid in the submersible slurry pump is completely discharged. If the rotor is disassembled, drain the lubricating oil in the rotor bearing housing. If the newly added oil is stored,MilwaukeeVertical heavy-duty slurry pump, it should continue to be used after maintenance. Do not dump it directly　　How to avoid: the impeller body and shaft are connected with keys and the end is locked with impeller nuts. Because the outer diameter of the impeller nut is small, the torque during reflux is small, so it can well prevent reverse loosening caused by reflux. Of course, there are many details　　 Then reinstall the equipment on the engine and install the rubber hose.Design brand,　　When using the sand pump, be sure to pay attention to the steering divergence between the motor and the pump. The sand pump has an arrow on the pump to mark the main steering. After the power supply is connected, run the pump without load. Check whether the motor operates normally. During operation, be careful not to exceed the bearing on the pump support to avoid　　Submersible slurry pump is a kind of pump used in mines. Do you know the effect and form of its shaft seal? Let&#;s have a look.　　The above is about how to replace the water seal of Boshan submersible slurry pump. In addition to the water seal, other parts of the pump also need to be replaced in time when they are damaged. Moreover, some parts of the pump are relatively easy to be damaged so we need to replace them regularly during use　　Check whether it needs to be replaced.

　　Stability and reliability of seals between pump bodies.Quality improvement, a smooth surface can be formed on the surface.　　 Check the insulation resistance of the motor every four weeks and make records.　　What stands out is the sealing of the container. The seal is easy to install and maintain, stable and reliable, but the price is quite expensive.Milwaukee,　　Turn on the power supply type fool operation; It has a wide range of applications. In many cases, it belongs to a portable workstation,MilwaukeeSmall deep well pump, which can be brought wherever it is needed, because it does not need too many auxiliary facilities.　　Normal operation. The submersible slurry pump can transport the slurry with corrosive or solid particles, coal slurry heavy medium transportation and dredging the river. When the equipment is pumping sand, some sand layers around the equipment will make the equipment covered by a large amount of sediment, we should choose　　The of descending axial force can be used for slurry transportation in power plants, hydraulic and other professions; The mechanical seal is tight and reliable,MilwaukeeWater well pipeline pump, and the leakage probability does not exceed drops /min, which is mostly used to transport flammable, explosive, toxic, strong corrosive and valuable liquids or materials with high temperature, high pressure and low temperature.