PetropolisOil immersed transformer manufacturerThere are several ways to install the structure

122HP117294921   ·  2023-05-09 04:29:56   ·   Machinery and industry equipment

The iron core of power transformer is made of high-quality crystallized hot-rolled ferrite core, which is stacked at the degree fully inclined multi-step interface. The surface is covered with epoxy resin adhesive cable sheath coating, which is resistant to corrosion and rust, and has sound insulation and noise reduction.When leaving the factory, the production and processing are not smooth and the sealing is poor. The common fault of oil leakage will be caused after the oil transformer is sealed for a period of time.Petropolis,Once the insulation material of electrical equipment is overheated, the surrounding gas will cause a kind of odor. This kind of odor can be sniffed out by normal patrol staff. When you smell such odor during normal inspection, you should carefully inspect the equipment and parts until you find out the cause.Before no-load impulse closing, the transformer shall be placed for h, and the rising seat and waterproof sleeve installed with vent plug shall be deflated on time.KojeDifference between dry-type transformer and oil immersed transformer:A specific part of dry-type transformer is the hanging core of dry-type transformer. The hanging core of dry-type transformer is a vital component. How to carry out the hanging core?When we apply oil immersed transformer, we all know that it works with the help of oil. What if the oil immersed transformer is on fire? What countermeasures should we do?


PetropolisOil immersed transformer manufacturerThere are several ways to install the structure



When we apply oil immersed transformer, we all know that it works with the help of oil. What if the oil immersed transformer is on fire? What countermeasures should we do?Transformer inspection nose sniffing methodBefore no-load impact closing, the pose period of overcurrent protection shall be set to zero, and the data signal circuit of steam vehicle relay shall be temporarily connected to the pull-in circuit.High quality brand,When the full load test is carried out and everything is normal,PetropolisPrice list of power transformer, the load can be connected.The noise of dry-type transformer is mainly the vibration noise in operation. This vibration noise is caused by multiple positions,PetropolisS11 parameters of oil immersed transformer, including the vibration of magnetic induction electromagnetic coil. All pay great attention to the solution of vibration when carrying out noise control.The whole process of hanging the core of dry-type transformer is more critical, and there are many situations that the hanging core of dry-type transformer must pay special attention to. Therefore, the hanging core of dry-type transformer should be carried out according to the above matters, so as to promote the safety of dry-type transformer!


PetropolisOil immersed transformer manufacturerThere are several ways to install the structure



The method and whole process of taking oil sample of power transformer are as follows:Quality department,Brief introduction of zero line of power transformerThere is a magnetic induction line crossing in the transformer core, and must be technically as a certain pillar. Only in that way, the performance of dry-type transformer will be more stable. What are the common manufacturing processes and steps of dry-type transformer?Petropolis,It is generally made due to unreasonable installation or ineffective sealing. Polymer composite materials can bond metal materials porcelain, laminated glass and other materials very well, so as to achieve the pressure management of oil leakage.If the above provisions are not met, the problem of dryness shall be solved. Generally, it is OK to operate the centrifugal fan for a period of time. Check the cleanliness of the power transformer. If too much dust is found, it must be eliminated to ensure indoor ventilation and avoid insulation penetration. In particular, pay attention to cleaning the insulators of the power transformer and the top and bottom ends of winding resistance installation. Portable centrifugal fan or dry air compression or N shall be used to clean the dust in indoor space that is not easy to reach,PetropolisHigh current transformer, such as ventilation duct, and there shall be no dirt.After the oil is drained, all anchor bolts of the automobile oil tank at the upper end of the detachable oil cover shall be tied with the lifting jack, and the lifting point shall be on the common earrings or bolts. If necessary, the human resources traction belt shall be used as a guide.

5 Replies   |  until 2023-05-09 04:29:56 | 155 Views

Kaihan Machinery Manufacturing Co., Ltd. 2023-05-09 11:48:31 support  0 | be opposed to  0

Really a good seller. I have to find you if I have this PetropolisOil immersed transformer manufacturer demand in the future!

sale of flowers 2023-05-09 13:48:35 support  0 | be opposed to  0

Ha ha. PetropolisOil immersed transformer manufacturer It’s here so soon, it’s not bad, next time you come, you can ask for a discount ^_^

Contract Energy Management Services 2023-05-09 12:34:39 support  0 | be opposed to  0

The quality is very good, exactly the same as the seller’s description, very satisfied, really like it, completely exceeding expectations, the delivery speed is very fast, the packaging is very careful and strict, the logistics company’s service attitude is very good, the delivery speed is very fast, and I am very satisfied One time shopping.

Chemical product retail 2023-05-09 12:58:29 support  0 | be opposed to  0

You PetropolisOil immersed transformer manufacturer are good, is it convenient to place an order?

conference system 2023-05-09 11:56:02 support  0 | be opposed to  0

Haha, PetropolisOil immersed transformer manufacturer received! It's too late to confirm, sorry, the boss is very fashionable!
Log inContent can only be published later