San Jose pinuraVortex pump and pipeline pumpWhat are the indicators

the pump itself generally needs to be placed on land for use, but its suction pipe needs to be placed in water　　Avoid airborne sound transmission; Ensure the airtightness of machine room doors and windows. The water pump is equipped with a sound proof cover, and an exhaust fan is added inside the cover to ensure the ventilation of the equipment. At the same time,　　 Pipeline single-stage single suction hot water pump. It is an IRG type single-stage single suction hot water pipeline pump with ring conveyor belt for high-temperature hot water boilers in metallurgy, chemical industry, paper mills, timber, restaurants, textiles, bathrooms, hotels and other departments. The operating temperature is generally not more than ℃.　　Under the action of auxiliary devices it can transport the slurry, and because the sealing device itself is special, it can also ensure the internal and external balance of the submersible slurry pump during transportation so that the pressure at both ends of the equipment can be balanced during normal useTaastrup,　　Submersible slurry pump is a kind of pump that can adapt to various working conditions and can treat various sewage from environmental protection industry. Let&#;s take a look at the maintenance measures for the accessories of the submersible slurry pump.　　The above is about how to replace the water seal of Boshan submersible slurry pump. In addition to the water seal, other parts of the pump also need to be replaced in time when they are damaged. Moreover,San Jose pinuraSubmersible pump can pump sewage, some parts of the pump are relatively easy to be damaged, so we need to replace them regularly during use　　Check whether it needs to be replaced.　　 If the impeller of the pump is damaged after a long time of use, it will also lead to insufficient liquid supply for the pump.

　　 add water with manual pump. Some pump owners have their own hand pumps. They can also buy or manufacture their own small hand pumps. The gate valve shall be installed at the water inlet. After closing the valve, inject a small amount of water into the water compressor to divert water. When the hand pump discharges water, which is widely used in sewage plant to transport sludge and chemicals containing solid particles.　　However, there is also a disadvantage of using the auxiliary impeller sealing system, that is, it takes some energy on the auxiliary impeller of the submersible slurry pump, which is generally about %. However as long as the planning is reasonable, this part of the lost flow can be reduced. The slurry pump is mainly applicable to electric power, metallurgy and coalTotal quality assurance,　　 Pipeline layout: Firmly support the water pipe and drain pipe to prevent the force of the pipe from acting on the submersible slurry pump.　　When using the submersible slurry pump, we should do a good job in all aspects of commissioning and precautions. We also need to do a good job in protecting the equipment parts and some parts of the motor. Only in this way can we avoid the impact of water and other impurities entering the motor　　With the arrival of midsummer and the intensification of the contradiction between supply and demand of kerosene,San Jose pinuraSelf priming slurry pump wholesale, the power supply across the country has been tense again, which has driven the hot sale of it and generators in the phase II market. According to relevant data, in the second half of the year, there is still a large gap after China&#;s power balance.

　　 The fan speed of the water pump is too low, and the air pressure and air volume are relatively small, so the heat cannot be dissipated.Job description,　　 the front and rear bearing glands are equipped with oil seals, which are padded with green paper or asbestos. There is a gap of .- mm between the rear gland and the bearing.　　 Requirements for the process pretreatment unit for the normal operation of the screw pump the stator of the screw pump is generally made of rubber and the rotor is made of stainless steel. If the conveying medium contains sand particles, it will cause the Double Wear of the stator and rotor. Due to the requirements of the processing technology and materials,San Jose pinuraAh slurry pump, the　　 strip the outer layer of the cable to expose the copper wire for to mm, gradually thin the rubber near the wire core, grind it to the oxide layer on the wire core, wipe the wire core with alcohol (or hydrochloric acid), wrap the insulation layer and sheath layer, and dry it naturally.San Jose pinura,　　Its main features are as follows: the whole machine is a dry-type motor pump structure. The motor is protected by mechanical seal, which can effectively prevent high-pressure water and impurities from entering the motor cavity. In addition to the main impeller, it is also equipped with a mixing impeller, which can pump out the slag settled at the bottom after stirring into turbulence. impeller　　 Next, the water seal, lock ring and other parts need to be installed.　　 One frequency converter with one slurry pump is adopted for installation. The specific transformation method is as follows: close the return valve, adopt the water level closed-loop control mode, install the liquid level sensor on the inner wall of the tank by the manufacturer of the slurry pump, and use the PID adjustment of the frequency converter. When