San JoseISG single stage vertical pipeline pumpApplication in light industry

　　Sex is different. Although the submersible slurry pump is widely used the correct application is very important. Due to the limitation of the name of the slurry pump, some people outside the industry misunderstand this. In fact,San JosePipeline pump, the impurity pump, dredging pump, desilting pump, etc. are all in the application scope of the slurry pump　　Water flow into the bearing damages the bearing.San Jose,　　Its working principle is as follows: when the screw pump is working, the liquid is sucked into the sealing cavity formed by the rotor and stator. Due to the rotation of the rotor, the liquid follows the sealing cavity to move along the axial direction from the suction side to the discharge side of the pump, and the continuous suction and discharge realize the liquid transmission .　　Turn on the power supply type fool operation; It has a wide range of applications. In many cases, it belongs to a portable workstation, because it does not need too many auxiliary facilities.Abalak,　　The use of water pumps for agricultural drainage and irrigation can improve the ability of agriculture to resist natural disasters, which is measured by the pump efficiency. The pump efficiency is the ratio of the effective power and the shaft power and provide material conditions for agricultural mechanization and water conservancy.　　Where ρ—— Density of transmission medium liquid (kg/m; γ—— Gravity of medium liquid (n/m; H -- pump lift (m); Q - water pump flow (m/s); G - gravitational acceleration (m/s.　　The difference between the shaft power P and the effective power PE is the power loss in the pump, which is measured by η Indicates.　　After the submersible slurry pump leaves the factory, there is generally only outgoing cable, and the user needs to connect it separately during installation. If the connection is wrong, it will seriously affect the normal operation of the pump, so we should follow the correct steps to connect.

　　When the equipment is in use, the water delivered in the pump receives the friction with the surface of the pump impeller, so the pump needs to consume more energy to reduce the friction and resistance caused by the surface when it is rotating. Water will slowly overcome it as it flows　　Domestic stainless steel pipeline pump products have greatly improved their technical level through introduction,San JoseVertical centrifugal slurry pump, absorption, renovation, digestion and innovation. In particular, the supporting products of some major technical equipment have reached or approached the advanced level of similar products. With the continuous expansion of the market, stainless steel pipeline pump　　When in use, it can drive the impeller to rotate so as to drive it to flow.Standard requirements,　　 The bus voltage where the motor is located is V. Due to the uneven cable voltage drop and load distribution, it is also possible that the temperature is too high due to the low voltage of the water pump.　　Under the action of auxiliary devices, it can transport the slurry, and because the sealing device itself is special, it can also ensure the internal and external balance of the submersible slurry pump during transportation, so that the pressure at both ends of the equipment can be balanced during normal use　　 One frequency converter with one slurry pump is adopted for installation. The specific transformation method is as follows: close the return valve, adopt the water level closed-loop control mode, install the liquid level sensor on the inner wall of the tank by the manufacturer of the slurry pump, and use the PID adjustment of the frequency converter. When

　　What should be paid attention to in the process? Let&#;s learn about the precautions for using the submersible slurry pump. When the equipment is in use, the pump itself generally needs to be placed on land for use, but its suction pipe needs to be placed in waterMarket trend,San JoseSubmersible non clogging slurry pump,　　The equipment is integrated with the oil cooler, with compact layout. The water pump meets the modular and integrated design requirements of diesel engine parts. The joint surface with oil cooler adopts rubber sealing method, which has good sealing effect. Submersible slurry pump is a kind of solid-liquid mixing medium with the help of centrifugal force　　Try to select the pump with appropriate lift.　　 The secondary pump shaft seal of the two-stage series pump is (packing seal), and the startup of the series pump also follows the above method. Only after the first stage pump is started, the submersible slurry pump can open the outlet valve of the last stage pump (the opening size is based on the motor current of the first stage pump as the rated powerSan Jose,　　 Dust and oil stains on the motor reduce the heat dissipation capacity of the equipment and cause the equipment temperature to rise.　　 If the power cord is not well contacted, it is necessary to replace the new impeller in time for use.