BilinaVertical slurry pumpmanagement idea

　　Some of them are OK. For irrigation and other purposes in fact, we choose to use larger flow. Let&#;s take a look at the method of selecting pumps.　　It is occasionally found that there is insufficient liquid supply when using, so what are the reasons for this situation and how to deal with it.Bilina,　　 before starting, check all circuits and switches to see if their wiring is correct and reliable,BilinaVertical slurry pump, then turn them over the ground for ~ minutes (the time should not be too long to avoid damaging parts or burning motor windings), and check whether the motor running direction is correct. If the above problems are not found, it can be started　　Discount. In order to meet the needs of industrial production and make the submersible pump to achieve the ideal use effect, accurate and reasonable selection is very important. In order to select the pump reasonably and correctly, the following aspects need to be considered: Selection of shaft seal form: shaft seal of submersible slurry pumpVoorburg,　　If the oil seal ring of the shaft is seriously worn, replace it with a new one.　　 If there is no corresponding water leakage sensor, it is necessary to regularly maintain the submersible slurry pump and replace the seals.　　In addition to the method, materials shall be selected comprehensively according to the nature of corrosive medium, corrosion mechanism of water pump and stress characteristics. In order to prolong the service life, protection should be done well, which should be a comprehensive optimization design method.

　　When the water pump is driven by electricity or diesel engine, its impeller (like an electric fan) rotates wildly, thus forming a vacuum in the impeller. In this way, the atmospheric pressure will move the water pressure to pump water. In fact, from a al point of view, it is to convert electrical or chemical energy into gravity　　The water pump spindle is bent, and the spindle is not parallel to the motor spindle.　　The installation of submersible slurry pump is a step that needs to be concerned. Since we all care about it, it is mainly because the installation will directly affect the use effect. The installation work should be seamless. Some key operating points can be seen when installing the slurry pump.safety requirements , it is necessary to timely adjust the clearance between the impeller and the front guard plate. When adjusting the impeller clearance, first stop the pump, loosen the bolts pressing the bearing box, loosen the adjusting nuts make the bearing components move forward, and roll the shaft by hand to press the　　 the submersible slag pump is often used to transport pulp containing solid particles, so the wear resistance of the pipeline should also be considered.　　Water flow into the bearing damages the bearing.

　　Sex is different. Although the submersible slurry pump is widely used, the correct application is very important. Due to the limitation of the name of the slurry pump, some people outside the industry misunderstand this. In fact, the impurity pump, dredging pump, desilting pump, etc. are all in the application scope of the slurry pumpQuality inspection report,　　With the continuous development of slurry pump technology, submersible slurry pump appears in response to market demand. It is especially suitable for the depth at which the vertical slurry pump cannot operate. The underwater part of the vertical slurry pump is generally not more than m, and of course it can be more than. For example,BilinaSubmersible non clogging slurry pump, the maximum design depth of our company&#;s underwater slurry pump can reach m, but such underwater depth is not the best operating depth of this kind of pump, so it will lead to the unreliability of the operation of the vertical slurry pump from time to time.　　Dynamic water level: after the pump operates normally, the water inflow in the pool and the pumping capacity of the deep well pump reach an equilibrium point, and the water level at this time is called dynamic water level.　　The effective power is also called output power which is expressed by PE. It is the effective energy obtained in the pump by the medium liquid output from the pump in unit time.Bilina,　　 When the slurry pump fails to absorb water during operation, it may also be because the bottom valve is not opened. At this time, it is necessary to check whether the bottom valve is open and make corresponding adjustment.　　The water pump is not only the water supply for the city, but also the household water purifier used in our home. There is a with pump equipment to help us purify water. In any way, each of which has different sizes, volumes and s. Therefore, many people believe that　　 First remove the pump from the engine.