BraggScrew deep well pumpOur economy is gradually moving towards digitization

　　The non service life of the equipment is not as long as possible. If it is not used for a long time, but also reduce the service life of the parts.　　 First of all, let&#;s understand the causes of insufficient liquid supply: If the liquid level stored in the circulating liquid storage tank is lower than %, then insufficient liquid supply will occur when it is in use. Or the pump adds too much lubricating oil, which leads to accumulationBragg,　　 Change the oil: if the oil contains water drain it, change the oil,BraggAh slurry pump, seal the gasket, and then tighten the screw plug.　　Reasonable.Al Bab,　　The above is the correct sequence of impeller disassembly of submersible slurry pump. Because different types of pumps have some differences in structure, we also need to refer to the instructions when disassembling.　　Whether it is the pre installation inspection or the post installation commissioning inspection, the correct operating procedures must be strictly followed. Only the correct operating steps can make the product play an effective role in the use site.　　 First of all, we need to choose equipment with formal certificates when making choices. We must avoid buying some obsolete or inferior products. And sometimes when the pump is in use, multiple pumps need to be used in parallel or standby pumps need to be prepared.

　　 If the hot water within ℃ is recommended, the hot water pump must be used, and the external tap water shall be connected for cooling during operation, otherwise the motor will not be burned due to too high medium temperature.　　Whether there is any fault.　　For example, concentrate and tailings are treated in the concentrator, ash and slag are removed from the power plant, and slurry is transported in coastal river mining operations. The weight concentration of the treated slurry is: mortar %,　　Submersible slurry pump In addition, the sewage pump is usually driven by a motor, which also requires some time og quantity when switching on and off, so in fact, it can be adjusted to a certain extent during use. The submersible slurry pump needs to use a line when in use　　Therefore the correct selection of shaft seal can ensure the safe and stable operation of slurry pump.　　So it is called: submersible slurry pump.

　　Although the shaft seal occupies a small position in the pump, the normal operation of the pump is closely related to the shaft seal.Excellent service, the equipment must be regularly maintained and overhauled to avoid blockage. As the name suggests, the water pump is mainly used to transport water when it is used. The effect of normal pumps is often better when it is used, but in fact, we use it at ordinary times　　 Pipeline pump: the pipeline pump is a centrifugal pump with the same inlet and outlet in the same straight line and the same caliber. It can be installed in series at any position of the pipeline like a section of pipeline,BraggZD slurry pump, so it is called pipeline pump. It is defined and named according to the special appearance of the pump. If it is named according to the principle, the pipeline pump is a special structure　　Friction resistance due to bearing and packing; Friction between impeller and water during rotation; The vortex of water flow in the pump, gap reflux, inlet and outlet impact and other reasons. A part of the power must be consumed, so it is impossible for the water pump to completely change the power input by the power machine into effective power, in which the constant active powerBragg,　　The development of submersible slurry pump is to adapt to increasingly complex working conditions, facilitate users to use, and its use mode is more flexible. And it fills a part of the gap in the application of slurry pump. When the submergence depth is deep and there is no better slurry outlet, that is,BraggWear resistant slurry pump, in the traditional slurry pump　　Some of them are OK. For irrigation and other purposes, in fact, we choose to use larger flow. Let&#;s take a look at the method of selecting pumps.　　The purpose is to inject liquid higher than . MPa from the water seal ring to prevent gas leakage into the pump when the suction inlet of the submersible slurry pump is in a vacuum state. When the water pressure in the pump is higher than . MPa, the sealing fluid .-. MPa higher than the pressure in the pump can be injected to seal and reduce leakage