GuazarWear resistant slurry pumpLet’s take you to understand the performance characteristics and application scope

　　 If the hot water within ℃ is recommended, the hot water pump must be used, otherwise the motor will not be burned due to too high medium temperature.　　Through the introduction, we learned that the submersible slurry pump can be used to transport slurry when it is used at ordinary times. The relationship between its special structure is very close, but in fact, it also needs to be used in a correct way when it is used at ordinary times. Only in this way canGuazar,　　 Before using the pump, carefully check whether the cable is damaged,GuazarWear resistant slurry pump,GuazarBooster pipeline pump, whether the fasteners are loose or fall off, and whether the pump is deformed or damaged during transportation, storage and installation.　　 When the power supply voltage is too low, the pump will be overloaded, because the pump is also widely used in many rural watering. In this case, it may be lower than the rated voltage, so the current in the stator winding will also beNassau,　　Fourth, model selection parameters: outlet diameter, flow, dust, motor power impeller speed, pumping rate, maximum particle and weight.　　Schematic diagram of vertical slurry pump II. Why does the demand for submersible slurry pump increase greatly? From the perspective of market demand, although the absolute number of submersible slurry pumps has not exceeded that of vertical slurry pumps, it has a rapid development momentum, mainly due to the convenience and flexibility mentioned above; In addition, for submersible slurry pump　　 Moreover, the processes of these two pumps are also different, and the sewage pump can generally be adjusted. Submersible pumps are generally used in some special or other places.

　　 Move the sand pumping site frequently. When the pump pumps sand at a fixed position and drops to a certain height, lift the submersible slurry pump and move it to the adjacent position of the previous sand pumping place to continue pumping sand, so as to move the sand pumping place back and forth for sand pumping, so that the sand pumping area in this area forms a honeycomb,　　Replace the ball bearing of the motor.　　The non service life of the equipment is not as long as possible. If it is not used for a long time, it will not only easily corrode the parts, but also reduce the service life of the parts.Management Department,　　There is a difference between submersible slurry pump and sewage pump. Although the media conveyed by the two are not pure water and other media, the difference between slag slurry and sewage is still large. Let&#;s take a look at the difference between the two.　　 repair and level the welding part of the submersible slurry pump with a file, clean the part to be bound with alcohol again and wipe it dry.　　Therefore, the correct selection of shaft seal can ensure the safe and stable operation of slurry pump.

　　 Dust and oil stains on the motor reduce the heat dissipation capacity of the equipment and cause the equipment temperature to rise.Potential development　　It, generator and market formed at the beginning of construction have gradually formed a certain scale after more than ten years of rapid development. In the early stage, in order to meet the needs of market development, generators and other mechanical and electrical products were collectively moved to the phase II market for operation. With a good business environment,GuazarQuotation slurry pump, water pumps and generators　　 for new or replaced deep well submersible pumps, after hours of use, check whether the seal is good. In the future check it once a month. At the same time, check whether the shielding sleeve between the motor rotor and stator is well sealed. Try to reduce the number of starts in use.　　Head refers to the energy obtained from the pump by the unit weight of liquid output by the pump, so head refers to the effective energy obtained from the liquid output by the pump in unit time - that is, the effective power of the pump: the equation is PE= ρ GQH (W)= γ QH (W)Guazar,　　When using the submersible slurry pump, we should do a good job in all aspects of commissioning and precautions. We also need to do a good job in protecting the equipment parts and some parts of the motor. Only in this way can we avoid the impact of water and other impurities entering the motor　　There are many types of submersible slurry pumps available in the market, and different pump models have different performance and application fields. Therefore, although the pump has a wide range of applications, its application effect will be great　　The non service life of the equipment is not as long as possible. If it is not used for a long time, it will not only easily corrode the parts