TrebicWQ submersible pump parametersHow to check before use
The use of water pumps is related to all aspects of our life. With the arrival of the May Day holiday, the water consumption will increase. Therefore, it is necessary for us to choose a suitable water pump. In addition to the main impeller inside the equipment, a set of impeller for mixing will be added at the bottom of the equipment, Before using the pump so that the equipment can be used without itsTrebic, carefully check whether the cable is damaged, whether the fasteners are loose or fall off, and whether the pump is deformed or damaged during transportation, storage and installation. The submersible slurry pump is a slurry pump which is connected with the motor and works under the water at the same time. Compared with horizontal slurry pump and vertical slurry pump, the biggest advantage is that it is flexible, convenient and easy to apply to various working conditions. The most important technical point of submersible slurry pump is the tightness between its motor and pump body Stability and reliability of seals.Baile Atha Luain,TrebicLong shaft submerged slurry pump, Slurry pump Inappropriate model is selected when selecting the pump. In actual use, when the load conditions do not match the model of the slurry pump, for example, the pump lift used is too high or too low, which will lead to overload, so we are selecting the pump If it is found that the impeller is damaged and the liquid supply is insufficient, it is necessary to replace the new impeller in time for use. Ensure that the service time will be extended when it is used. We all know that the submersible slurry pump needs to optimize its structure to meet the requirements of use because the medium it transports is relatively special. The structure has been optimized to
If the head of the submersible slurry pump is too low or the head is higher than the practical condition, the flow will be large and the current will rise. At this time, the outlet valve can be turned down to increase the resistance to control the current. When assembling the motor and water pump departments below grade , firstly, tighten the nuts evenly between the water inlet joint and the contact plane from the upper part to the bearing seat, install the coupling, pump shaft, fixed studs and lock rings, fix the impeller and conical sleeve on the pump shaft with a damp cylinder, and install the guide housing and impeller Most of the time, we don&#;t know how to choose the pump when we buy it. In fact, we only need to choose the appropriate equipment according to our own use needs when we choose it. It&#;s more like that in a conventional family, the flow is smallVariable cost, First, screw down the bolts on the side bearing pressure cap, and then remove the nuts used for the connection between the three parts: discharge section, stuffing box body and bearing body; Then screw off the round nut on the shaft, and successively install the bearing inner race, bearing gland and retaining sleeve The above is the reason for the insufficient liquid supply of the water pump when it is in use, as well as the specific methods to deal with this situation. We should pay attention to the regular inspection of the equipment during normal use to ensure that it is in use Submersible slurry pump In addition, the sewage pump is usually driven by a motor, which also requires some time og quantity when switching on and off, so in fact it can be adjusted to a certain extent during use. The submersible slurry pump needs to use a line when in use
Body. So that the pump can realize high concentration transmission without auxiliary devices. The unique sealing device can effectively balance the pressure inside and outside the oil chamber, so that the pressure at both ends of the mechanical seal can be kept balanced, which maximizes the reliable operation of the mechanical seal and greatly extends its service lifeindex, What is the order. Attachment: data sheet required for ordering deep well pump The submersible slurry pump usually relies on water cooling to dissipate heat. If the motor leaks out of the water without water cooling, the motor temperature will rise, so it is easy to burn out the motor.Trebic, strip the outer layer of the cable to expose the copper wire for to mm, gradually thin the rubber near the wire core, grind it to the oxide layer on the wire core wipe the wire core with alcohol (or hydrochloric acid), wrap the insulation layer and sheath layer, and dry it naturally. If the impeller of the pump is damaged after a long time of use