GalatsonLong shaft submerged slurry pumpIndustry market

　　In fact, the impeller clearance of submersible slurry pump is not adjustable for all types of pump but it is adjustable. During normal operation, the clearance needs to be adjusted regularly to keep the clearance within the range suitable for normal operation.　　 Why does the demand for submersible slurry pumps increase greatly? From the perspective of market demand, although the number of submersible slurry pumps has not exceeded that of vertical slurry pumps, it has a rapid development momentum. The main reason is that the above-mentioned use is convenient and flexible; In addition,　　 Determine the head h. After the flow is determined, determine the inlet and outlet pipe diameters of the pump, complete the layout of the whole pipeline, and determine the head. In the actual selection, the resistance coefficient of the pipeline is often too large. In addition, when selecting the pump model, a head margin is added, resulting in　　Stop, then tighten the bearing seat, press down the nut, and fix the axial position of the rotor. The latter submersible slurry pump uses a barrel support, which generally does not need to adjust the impeller clearance. Therefore, if there is a problem with the clearance in the future use, loosen the support clamp first, and say that the nut is looseTema,　　 If the pump is equipped with a vacuum gauge or pressure gauge close the cock connected with the submersible slurry pump before starting the motor, open it after the speed is normal, and then gradually open the outlet sluice valve. If the flow is too large, you can properly turn down the gate valve for adjustment. Otherwise, if the flow is too small,Open the gate valve.　　Submersible slurry pump it fills the gap in the application of slurry pump. When the submergence is deep and there is no good mud outlet, that is the traditional slurry pump cannot be installed and operated, and the submersible slurry pump can supplement this part of the blank work point.　　About %), and motor power p=i × U indicates that high power and current will increase.

　　Will be scrapped. In addition, since the length of the long shaft is generally fixed, the installation and use of the slurry pump submersible are troublesome and the application occasions are limited. It is normal to use the equipment for a long time, for example, when the submersible slurry pump is used at ordinary times, air holes usually appear　　Slide until the active coupling is in place. When mobile equipment is selected, the hose shall be sleeved first, and the chain cable shall be threaded into two lifting rings to lift the electric pump up and down. Be careful not to use the cable as a rope to avoid danger.　　 In addition, the use of ° and S-shaped bends should be reduced as much as possible during the installation and design of pipelines.agent,　　Compared with the vertical slurry pump, the application market is also larger. In addition to the existing industrial and mining applications of the vertical slurry pump, the submersible slurry pump can also be used as a mobile slurry pump, such as sand pumping on board, etc; Submersible slurry pump assembly workshop III. what are the advantages of submersible slurry pump　　 It may also be because the pump&#;s liquid supply pipe is blocked by other substances during normal use.　　The disc friction loss of the slurry pump impeller will decrease with the decrease of the impeller diameter so that the pump efficiency of most low specific speed pumps will improve slightly after the impeller is cut. After cutting, keep the blades overlapped to a certain extent, and the degree of blade overlap will decrease with the addition of specific speed

　　 First, screw down the bolts on the side bearing pressure cap,GalatsonVertical centrifugal slurry pump, and then remove the nuts used for the connection between the three parts: discharge section, stuffing box body and bearing body; Then screw off the round nut on the shaft, and successively install the bearing inner race, bearing gland and retaining sleeveWork courses,　　In order to ensure the demand for water and electricity for production and living, many units, hotels and residential areas in various provinces and cities in China have purchased it and generators. Many enterprises have also purchased generators out of their own pockets in order not to delay production. Driven by this, it and the generator naturally become popular　　Unchanged.　　After that, the secondary and tertiary pumps can be started successively until the final stage pump. After all the series pumps are started,　　.　　When the submersible slurry pump works, the pump needs to be placed on land, the suction pipe needs to be placed in water,GalatsonCarbon steel explosion-proof pipeline pump, and the pump needs to be started. Due to special structural requirements, the slurry pump and submerged slurry circulating pump need to be placed above the water surface, so they need to be fixed, otherwise the motor will fall into the water　　Then there are new structures, such as thermohydrodynamic seals, backup seals and asymmetric molded metal single wall bellows seals.