Busgow FreiburgHousehold elevatorWhy is it so popular

To implement the arrangement of escalators and provide feedback, in order to determine the configuration of certain shared devices, the order of shipment, and the alignment of handrail turns during continuous arrangement.The household must make two steel splints above the entrance. The position and size of the clamp plate are determined based on the selected door machine model.Busgow Freiburg,Household elevators have gradually become an essential vertical transportation tool for modern single family, duplex, multi story, villa and other residential buildings, practical and convenient, and even a beautiful scenery in the home.The compensation chain and rope shall not collide with the shaft or other components during the operation of the elevator.Kouroussa,The household must make two steel splints above the entrance. The position and size of the clamp plate are determined based on the selected door machine model.The requirement for the shaft is that it should not be plastered, which is beneficial for reducing noise but there should be no protruding foreign objects.Measure the length, width,Busgow FreiburgSmall stage elevator, and depth of the pit (if any), and observe whether there are grooves and embedded parts at the support beam.

The call button on each floor is no longer working, and the call is cut off.The elevator stops on the first floor and the door does not move: the fire emergency landing function of the elevator is triggered by smoke or thermal sensors inside the building.If the elevator is in a downward direction, immediately close the door and return to the first floor station, and automatically open the elevator door.Test results,Machine room power supply: The power supply should be three-phase V, HZ, and the lighting power supply should be single-phase V, HZ. The incoming line should be connected to the vicinity of the machine room entrance and equipped with an incoming socket. Specializing in product and renewable resource business, including: home elevator manufacturersFor escalators that require intermediate support, it is necessary to determine whether the site has the conditions for adding support, as well as the range of support that can be added, the height and load size of the equipment and support platform and other parameters.Brick concrete structure elevator shaft: For unfinished brick structure shafts, arranged on three sides, and disconnected on one side of the elevator entrance. The distance between the center heights of the beams depends on the product model, and should not exceed mm. The beam height should be mm, and the thickness should be the same as the wall. The lower ring beam is -mm away from the bottom of the pit, and the higher ring beam is -mm away from the lower surface of the shaft roof. The completed framework with a solid brick structure shaft can be equipped with steel plywood at the position of the fixed guide rail support frame. The position and size of the plywood are provided by the elevator, steel beams can be considered to be added between the frames for rectification.

For escalators that require intermediate support,Busgow FreiburgSecond floor household small elevator, it is necessary to determine whether the site has the conditions for adding support,Busgow FreiburgAluminum alloy mast type lifting platform, as well as the range of support that can be added, the height and load size of the equipment and support platform, and other parameters.build,Measurement of elevator and escalator shafts (III)When accidentally trapped in an elevator, press the alarm bell inside the elevator, and call the elevator emergency rescue phone or community property phone for help. Do not open doors or mess with buttons, and patiently wait for rescue.The effective support width of the upper and lower support beams should be greater than the width of the escalator truss and there should be embedded steel plates.Busgow Freiburg,Attention: The elevator consists of two main parts: mechanical and electrical. If the elevator is not maintained on a daily basis, its safety cannot be guaranteed. If the elevator needs to be refueled without refueling, it will cause wear and tear on the mechanical components of the elevator, greatly shortening its service life and preventing normal use of the elevator.The mechanical components of the elevator's traction machine require oil. There are two scales on the outer cover of the traction machine. Open the oil nozzle to check that the oil should be in the middle of the two scales. If the oil is lower than the lower scale, it means that the traction machine should be refueled. If not refueled, the elevator will not operate well for a long time, leading to the burning of the elevator traction machine and motor. After the elevator has been running for a long time, the oil should be replaced in a timely manner to keep the traction machine clean and in good condition.　　“& rdquo; Elevator shaft: The design conditions are provided by the user to the architectural design department. The architectural design department analyzes whether the on-site pit depth, top floor height, reaction force, etc. can meet the installation requirements of the elevator, and develops a renovation construction plan. If it is indeed necessary to change the elevator structure due to civil engineering conditions (such as car size, door opening width, etc.), then consider the non-standard design of the elevator.