CharatenangoIrrigation deep well pumpYield strength of

　　 one method is to use ultrasonic method to detect whether the equipment has cavitation. This method is often convenient for re detection. Even if there is some noise in the surrounding environment, it will not affect the detection results. Therefore, many pumps tend to have better measurement results when in use.　　 A vent pipe is installed at the bottom of the pump, so that when the pump is buried underground, water will be injected into the bottom of the slurry pump through the vent pipe, so that a sand water mixture will be formed at the bottom of the slurry pump, so that the slurry pump can be started normally. The advantage of this approach is that even ifCharatenango,　　In addition, for different media pumped by the deep well pump, the pump components can be made of corrosion-resistant materials suitable for various media, L and other stainless steel.　　It should be /-/ between. When the packing is worn, the packing gland can be properly pressed. If it is worn too much, it should be replaced. The whole commissioning process of the submersible slurry pump mainly includes the above five tasks, which are mainly to pay attention to the details and the phenomena occurred during the operation,　　Stop, then tighten the bearing seat,CharatenangoPipeline pump,CharatenangoVertical multistage centrifugal pipeline pump, press down the nut, and fix the axial position of the rotor. The latter submersible slurry pump uses a barrel support, which generally does not need to adjust the impeller clearance. Therefore, if there is a problem with the clearance in the future use loosen the support clamp first, and say that the nut is loose　　The high-pressure water flows to the space occupied by the original bubble at a very high speed, forming an impact force. The metal surface of the pump was fatigued and damaged by these impacts. Cavitation is caused by air bubble rupture and material stamping due to the difference in air temperature and pressure　　 install a valve to inject water at the water inlet and outlet. This method is to install a valve on the water inlet pipe of the submersible slurry pump and connect the water pipe to inject water into the pump. This is a common and simple method.

　　 The pump body (can not) bear the pressure from the outlet pipeline system. The standby pump in the warehouse should rotate (/ times a week to make the shaft bear the load and external vibration evenly. The belt CR drive is that the motor is on the (right) side of the pump from the inlet of the pump.　　 If the three-phase current of the submersible sewage pump is large and stable, the submersible pump cannot be started. The reason can only be understood from the submersible pump. Submersible pump bearings may be damaged and the pump may be blocked. The impeller is full of groceries. Submersible pumps shall not be used for sundries, such as those wrapped around the pump shaft　　 for screws that are too tight or rusted for a long time, the nut can be lubricated with kerosene prepared in advance, or the nut can be gently knocked with a wooden hammer and then removed. This method can also be used in slurry pumps and other places.Scheme customization,　　The mixing impeller and other main flow passage parts are made of high wear-resistant materials, which are wear-resistant, corrosion-resistant, non clogging and have strong sewage discharge capacity, and can effectively pass through large solid particles. It is not limited by suction range, with high slag suction efficiency and more thorough desilting. No auxiliary vacuum pump is required and the investment is lower. nothing　　 Dust and oil stains on the motor reduce the heat dissipation capacity of the equipment and cause the equipment temperature to rise.　　Many users, including new practitioners of slurry pumps, often fail to distinguish the difference between submerged vertical slurry pumps and submerged slurry pumps. The names of submerged and submerged slurry pumps seem similar but there are essential differences. What is the difference between submersible slurry pump and vertical slurry pump?

　　 The gas inadvertently entered in the equipment is discharged and good sealing performance is ensured.Development Curriculum, so that the equipment can drive the solid to flow when it is in use　　Let the medium containing some solid particles generate a certain flow rate, so that the slurry can be transported. In terms of the principle of the submersible slurry pump, it is actually quite simple　　In addition to conventional accessories, ordinary long shaft pumps can also manufacture deep well pumps with different al characteristics according to the special requirements of customers. If it is required to improve the sealing performance of the pump seat packing,CharatenangoSubmersible sewage pump, the packing sealing can be changed into a mechanical sealing device. If there is backpressure water at the wellhead, the water consumption will increase. Therefore, it is necessary for us to choose a suitable water pump.Charatenango,　　Submersible pump is a common water lifting equipment for deep wells. During operation, the whole machine intrudes into the water to extract water from the underground to the surface. It is commonly used for domestic water, industrial cooling, farmland irrigation, seawater lifting, ship load adjustment, landscape fountains, etc. Submersible pump is generally divided into clean water submersible　　Basically, the reasons for the motor heating of the submersible slurry pump are the above items. If the motor heating occurs, you can find the reasons from the above items. However, it must be noted that if the fault is caused by electricity, people who do not know electricity should not repair it by themselves, so as to avoid people　　The impeller of the submersible slurry pump may need to be disassembled for maintenance or repair during use. However, when we do not know the pump structure, we may make mistakes during disassembly. Let&#;s take a look at the correct disassembly of the impeller