Gillard melenaSubmersible pump can pump sewageDo you know how to clean and repair

　　Slurry pump Inappropriate model is selected when selecting the pump. In actual use, when the load conditions do not match the model of the slurry pump, for example, the pump lift used is too high or too low, which will lead to overload, so we are selecting the pump　　Analysis of installation problems of slurry pump For bearings lubricated with thin oil,Gillard melenaBaigang deep well pump, oil shall be added according to the oil level line of the oil standard before start-up. Add (HL hydraulic oil in winter and (hl hydraulic oil in summer. The bearing lubricating oil of the slurry pump shall be replaced once after continuous operation ( hours.Gillard melena,　　 Check the voltage to see if the voltage is too low to drive. Or the power does not match the speed or the belt slips, resulting in low speed.　　The purpose is to inject liquid higher than . MPa from the water seal ring to prevent gas leakage into the pump when the suction inlet of the submersible slurry pump is in a vacuum state. When the water pressure in the pump is higher than . MPa, the sealing fluid .-. MPa higher than the pressure in the pump can be injected to seal and reduce leakageCam Ranh,　　The vertical sand pump is generally a submersible slurry pump. Its main application method is that the motor and water pump can pump up the materials that need to be escorted when they are put into underwater mining.　　For example, concentrate and tailings are treated in the concentrator, ash and slag are removed from the power plant, slime and dense medium coal are transported in the coal preparation plant, and slurry is transported in coastal river mining operations. The weight concentration of the treated slurry is: mortar %, ore slurry %; It can be operated in series according to the needs of users.　　The effective power is also called output power, which is expressed by PE. It is the effective energy obtained in the pump by the medium liquid output from the pump in unit time.

　　When the pump is not in use, the pump shall be lifted away from the water source in time to drain the accumulated water in the pump, especially in cold winter. Then put it in a dry place. Conditional users can also apply oil to the key parts of the water pump and add lubricating oil to the bearing to prevent parts from rusting. in addition　　And has a wide range of applications.　　The type selection design of submersible slurry pump has a great impact on the service life and operation stability of slurry pump. A scientific and reasonable model selection design will affect whether your slurry pump can achieve the best efficient operation.agent,　　Water or air leakage in the pipeline. The nut may not be tightened during installation. If the leakage is not serious, the air or water leakage can be treated with cement or cement slurry mixed with asphalt oil. Temporary repairs can be done with some wet mud or soft soap. If water leaks at the water pump joint, tighten the nut with a wrench. as　　Under the action of auxiliary devices it can transport the slurry, and because the sealing device itself is special, so that the pressure at both ends of the equipment can be balanced during normal use　　Many users, including new practitioners of slurry pumps, but there are essential differences. What is the difference between submersible slurry pump and vertical slurry pump?

　　Do not exceed the rated current.safety requirements ,　　The vertical sand pump is generally a submersible slurry pump. Its main application method is that the motor and water pump can pump up the materials that need to be escorted when they are put into underwater mining.　　The submersible sewage pump is mainly used to ensure various sewage pump products containing solid particles or other impurities. Because it works in water,Gillard melenaVertical centrifugal slurry pump, we call it a submersible sewage pump, and the model selection of the submersible sewage pump is often determined according to the parameter information such as the nature and working characteristics of the sewage pump station.　　 determination of model: for water pump or pump with physical and chemical medium similar to water, and make correction according to the performance table or performance curve of the model to see whether the normal working point falls in the priority working area of the pump.Gillard melena,　　 Then replace the pulley and pump cover plate and tighten the fixing nuts.　　When in use, it can drive the impeller to rotate so as to drive it to flow.　　Circumference. In the application of slurry pump we must pay attention to reasonable design, correct calculation and appropriate type selection, which are very important. In addition to the main wheel, a set of stirring impeller is added at the bottom of the product, which can spray the precipitated slag into a mixture of water and solid particles