According to the national standard of hot rolled H-section steel in China (GB / t-, H-section steel is divided into narrow flange, wide flange and steel pile, whose codes are Hz, HK and Hu respectively. Narrow flange H-section steel is suitable for beams or compression bending members, while wide flange H-section steel and H-section steel piles are suitable for axial compression members or compression bending members. Compared with H-section steel, W, IX and iy are not as good as H-section steel under the premise of equal weight. East West derusting: if the galvanized pipe surface is rusty, the manufacturer will choose East West derusting and polish it with a steel wire brushAfter determining the reasonable pickling agent and polishing solution,La ShevaHow much is DN50 galvanized pipe, it is very easy to carry out hot galvanizing for relevant alloy pipes. Use 'phosphating treatment' to degrease the pipes of electrolytic machine equipment, put them into the aqueous solution with zinc salt after pickling and passivation, connect the negative level of electrolytic machine equipment, put them into the cold-rolled steel plate in the direction corresponding to the pipes, and connect the switching power supply, If the current flows from the positive stage to the negative stage, a layer of zinc is deposited in the pipe.index,Passivation treatment operation of alloy pipeGB No. I-beam is in height, in leg width and in waist thickness.The shape of I-beam is similar to that of H-beam. What is the difference between them?
Main uses: as a finished material, flat steel can be used to make hoop iron, and used as building frame structural parts and escalators in buildings. Flat steel is divided into two types according to its shape: plane spring flat steel and single-sided double groove spring flat steel. Hot rolled spring flat steel is mainly used to manufacture leaf springs for automobiles, tractors, railway transportation and other machinery.Sincere service,Alloy pipe is a spiral seam seamless steel pipe, which is made of hot-rolled strip steel coil, often processed by warm extrusion and welded by automatic double wire double side arc welding process. The alloy pipe sends the hot-rolled strip steel to the welded pipe unit, and the hot-rolled strip steel is extruded through multiple passes. The hot-rolled strip steel is rolled slowly to produce annular pipe material with open mouth gap. Adjust the reduction amount of the extrusion roll to control the welding gap at ~ mm and make both sides of the weld flush.The correct and reasonable use of galvanized pipe can play a better role. The product can be widely used in the market because of its obvious performance advantages. Both strength and toughness are worth our choice. Lets see what the specific uses are and what the acceptance standards are? Direct rolling pass system. The direct rolling pass system refers to the pass system in which the two open legs of the I-beam pass are on the same side of the roll axis at the same time, and the waist is parallel to the roll axis.La Sheva,Because the section size of ordinary I-beam and light I-beam is relatively large and narrow, the moment of inertia of the two main shafts on the section is quite different, which limits its application range. I-beam shall be selected according to the requirements of design drawings. In the structural design,La ShevaHow much is a 25 yuan steel bar, the use of I-beam should be reasonably selected according to the mechanical properties, chemical properties, weldability and structural size of I-beam.The general alloy pipe with improved performance is variable and has high application value. The alloy pipe contains more Cr and is heat resistant Low temperature resistance Corrosion resistance. There is no aluminum alloy in plain carbon seamless steel pipe, not very little aluminum alloy, and the alloy pipe is used in crude oil Aerospace Chemical plant Power engineering heating furnace. Because the physical properties of alloy tubes are easy to change and adjust. Hot push hole diameter. More sensitive applications and facilities of such methods require simplicity, low cost, easy maintenance, durable economic development and convenient product specification transformation. For example, the production of large diameter must be grooved pipe, elbow and similar products. You only need to add some spare parts. The expansion method of hot push can be used to process and manufacture large-diameter, and can not exceed the working capacity of thick wall pipes of machinery and equipment.
Songyue Construction Engineering Company 2023-01-01 09:41:19 support 0 | be opposed to 0
Meibo Children's Toys Company 2023-01-01 09:18:45 support 0 | be opposed to 0
Electrical machinery and equipment manufacturing 2023-01-01 08:11:15 support 0 | be opposed to 0
Including sprinkler and micro-irrigation 2023-01-01 07:32:41 support 0 | be opposed to 0